EDA Consortium Reports Decrease for 2009 but Sequential Fourth Quarter Gains

SAN JOSE, CA -- (MARKET WIRE) -- Apr 01, 2010 -- The EDA Consortium (EDAC) Market Statistics Service (MSS) today announced that the Electronic Design Automation (EDA) industry revenue for Q4 2009 was $1262.7 million, an 8.1 percent sequential increase from Q3. On a Q4/Q4 basis, EDA industry revenue declined 4.2 percent, compared to $1318.7 million in Q4 2008. The four-quarter moving average declined 9.5 percent.

"Despite the year-to-year decrease, the EDAC revenue numbers continue to show a sequential increase over the previous quarter," said Wally Rhines, EDAC chair and chairman and CEO of Mentor Graphics. "Most notable sequential increases were in the categories of CAE, IC Physical Design, and semiconductor IP. In addition, the Pacific Rim region showed year-to-year growth both for Q4 and for the year as a whole."

Companies that were tracked employed 25,995 professionals in Q4 2009, down 4.8 percent from the 27,311 employed in Q4 2008, but up 0.2 percent from the 25,942 employed in Q3 2009.

Revenue by Product Category
Computer Aided Engineering (CAE), EDA's largest category, generated revenue of $482.3 million in Q4 2009. This represents a 3.9 percent decrease over the same period in 2008. The four-quarter moving average for CAE declined 9.8 percent.

In the next largest category, IC Physical Design & Verification, revenue decreased to $293.6 million in Q4 2009, a 1.0 percent decrease compared to Q4 2008. The four-quarter moving average declined 7.3 percent for IC Physical Design & Verification.

Printed Circuit Board and Multi-Chip Module (PCB & MCM) revenue decreased 3.4 percent compared to Q4 2008, to $131.4 million. The four-quarter moving average for PCB & MCM decreased 8.5 percent.

Semiconductor Intellectual Property (SIP) revenue totaled $272.7 million in Q4 2009, a 4.5 percent decrease compared to Q4 2008. The four-quarter moving average for SIP decreased 10.8 percent.

Services revenue was $82.7 million in Q4 2009, a decrease of 16.4 percent compared to Q4 2008. The four-quarter moving average for services decreased 12.7 percent.

Revenue by Consuming Region
The Americas, EDA's largest region, purchased $560.8 million of EDA products and services in Q4 2009, representing a 1.4 percent decrease compared to Q4 2008. The four-quarter moving average was down 8.1 percent for the region.

Revenue in Europe, the Middle East, and Africa (EMEA) was down 12.1 percent in Q4 2009 compared to Q4 2008 on revenues of $255.2 million. The four-quarter moving average for EMEA was down 16.6 percent.

Fourth quarter 2009 revenue from Japan decreased 9.6 percent to $236.3 million compared to Q4 2008. The four-quarter moving average for Japan decreased 13.2 percent.

The Asia/Pacific (APAC) region increased to $210.3 million in Q4 2009, a 6.3 percent increase compared to the same quarter in 2008. The four-quarter moving average increased 1.2 percent.

About the MSS Report
The EDA Consortium Market Statistics Service reports EDA industry revenue data quarterly and is available by annual subscription. Both public and private companies contribute data to the report. Each quarterly report is published approximately three months after quarter close. MSS report data is segmented as follows: revenue type (product licenses and maintenance, services, and SIP), application (CAE, PCB/MCM Layout, and IC Physical Design and Verification), and region (the Americas, Europe Middle East and Africa, Japan, and Asia Pacific), with many subcategories of detail provided. The report also tracks total employment of the reporting companies.

About the EDA Consortium
The EDA Consortium is the international association of companies that provide design tools and services that enable engineers to create the world's electronic products used for communications, computer, space technology, medical, automotive, industrial equipment, and consumer electronics markets among others. For more information about the EDA Consortium, visit www.edac.org, or to subscribe to the Market Statistics Service, call (408) 287-3322 or email Email Contact.

The information supplied by the EDA Consortium is believed to be accurate and reliable, but the EDA Consortium assumes no responsibility for any errors that may appear in this document. All trademarks and registered trademarks are the property of their respective owners.

Press Contacts:
Paul Cohen, EDA Consortium, 408-287-3322
Suzanne Graham, Mentor Graphics, 503-685-7789 





Review Article Be the first to review this article

SolidCAM: SolidCARE

Featured Video
MCAD Corporate Newsletter
rss feed
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
NVIDIA’s AI Computer Drives AVs
Jobs
Mechanical Engineer for The Planate Management Group LLC at Perry Point, MD
Senior Mechanical Engineer for Albert Kahn and Associates at Detroit, MI
Vice President, Transportation Services for Associated General Contractors of New York State at Albany, NY
ENVIRONMENTAL GRAPHIC DESIGNER for Blitz at San Francisco, CA
GIS Analyst for G2 Partners LLC at San Ramon, CA
GIS Software Developer for UDC at Englewood, CO
Upcoming Events
ASSESS 2017 CONGRESS at Bolger Center Potomac MD - Nov 1 - 3, 2017
FABTECH 2017 at McCormick Place Chicago IL - Nov 6 - 9, 2017
ATX MINNEAPOLIS 2017 at Minneapolis MN - Nov 8 - 9, 2017
2017 China Chongqing International Machine Tool Show (CCIMT) at Chongqing International Expo Center, Yubei Chongqing China - Nov 13 - 16, 2017



Internet Business Systems © 2017 Internet Business Systems, Inc.
25 North 14th Steet, Suite 710, San Jose, CA 95112
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise