EDA Consortium Reports Industry Revenue Down in Third Quarter 2009

SAN JOSE, Calif. — (BUSINESS WIRE) — January 14, 2010 — The EDA Consortium (EDAC) Market Statistics Service (MSS) today announced that the Electronic Design Automation (EDA) industry revenue for Q3 2009 is $1,167.9 million, a 3.8 percent sequential increase from Q2. On a Q3/Q3 basis, EDA industry revenue declined 7.2 percent, compared to $1,258.6 million in Q3 2008. The four-quarter moving average declined 13.1 percent.

“Just as the semiconductor industry has experienced sequential growth, the EDAC revenue numbers similarly represent a sequential increase over the previous quarter,” said Wally Rhines, EDAC chair and chairman and CEO of Mentor Graphics. “Most notable sequential increases were in the categories of printed circuit board, semiconductor IP, and services.”

Companies that were tracked employed 25,942 professionals in Q3 2009, down 7.9 percent from the 28,176 employed in Q3 2008, and down 1.4 percent from the 26,298 employed in Q2 2009.

Revenue by Product Category

Computer Aided Engineering (CAE), EDA’s largest category, generated revenue of $450.1 million in Q3 2009. This represents a 3.3 percent decrease over the same period in 2008. The four-quarter moving average for CAE declined 15.6 percent.

In the next largest category, IC Physical Design & Verification, revenue decreased to $260.8 million in Q3 2009, a 10.0 percent decrease compared to Q3 2008. The four-quarter moving average declined 16.9 percent for IC Physical Design & Verification.

Printed Circuit Board and Multi-Chip Module (PCB & MCM) revenue increased 1.5 percent compared to Q3 2008, to $132.9 million. The four-quarter moving average for PCB & MCM decreased 10.6 percent.

Semiconductor Intellectual Property (SIP) revenue totaled $240.7 million in Q3 2009, a 10.1 percent decrease compared to Q3 2008. The four-quarter moving average for SIP decreased 8.0 percent.

Services revenue was $83.5 million in Q3 2009, a decrease of 20.3 percent compared to Q3 2008. The four-quarter moving average for services decreased 4.0 percent.

Revenue by Consuming Region

The Americas, EDA’s largest region, purchased $511.2 million of EDA products and services in Q3 2009, representing an 8.0 percent decrease compared to Q3 2008. The four-quarter moving average was down 14.1 percent for the region.

Revenue in Europe, the Middle East, and Africa (EMEA) was down 17.6 percent in Q3 2009 compared to Q3 2008 on revenues of $204.0 million. The four-quarter moving average for EMEA was down 15.4 percent.

Q3 2009 revenue from Japan decreased 2.3 percent to $248.9 million compared to Q3 2008. The four-quarter moving average for Japan decreased 15.1 percent.

The Asia/Pacific (APAC) region increased to $203.8 million in Q3 2009, a 1.6 percent increase compared to the same quarter in 2008. The four-quarter moving average declined 4.7 percent.

About the MSS Report

The EDA Consortium Market Statistics Service reports EDA industry revenue data quarterly and is available by annual subscription. Both public and private companies contribute data to the report. Each quarterly report is published approximately three months after quarter close. MSS report data is segmented as follows: revenue type (product licenses and maintenance, services, and SIP), application (CAE, PCB/MCM Layout, and IC Physical Design and Verification), and region (the Americas, Europe Middle East and Africa, Japan, and Asia Pacific), with many subcategories of detail provided. The report also tracks total employment of the reporting companies.

About the EDA Consortium

The EDA Consortium is the international association of companies that provide design tools and services that enable engineers to create the world’s electronic products used for communications, computer, space technology, medical, automotive, industrial equipment, and consumer electronics markets among others. For more information about the EDA Consortium, visit www.edac.org, or to subscribe to the Market Statistics Service, call 408-287-3322 or email Email Contact.

The information supplied by the EDA Consortium is believed to be accurate and reliable, but the EDA Consortium assumes no responsibility for any errors that may appear in this document. All trademarks and registered trademarks are the property of their respective owners.

 



Contact:

EDA Consortium
Paul Cohen, 408-287-3322
or
Mentor Graphics
Suzanne Graham, 503-685-7789




Review Article Be the first to review this article

Featured Video
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
Re-Use Your CAD: The ModelCHECK Handbook
Jobs
Business Partner Manager for Cityworks - Azteca Systems, LLC at Sandy, UT
Upcoming Events
Design & Manufacturing, Feb 7 - 9, 2017 Anaheim Convention Center, Anaheim, CA at Anaheim Convention Center Anaheim CA - Feb 7 - 9, 2017
Innorobo 2017 at Docks de Paris Paris France - May 16 - 18, 2017
Display Week 2017 at Los Angeles Convention Center 1201 S Figueroa St Los Angeles CA - May 21 - 26, 2017
SolidCAM: Program your CNCs directly inside your existing CAD system.



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise