HP Brings DreamColor Accuracy to Mobile Power Users

More information is available in an online press kit at www.hp.com/go/SIGGRAPH08.

About HP

HP focuses on simplifying technology experiences for all of its customers from individual consumers to the largest businesses. With a portfolio that spans printing, personal computing, software, services and IT infrastructure, HP is among the worlds largest IT companies, with revenue totaling $110.4 billion for the four fiscal quarters ended April 30, 2008. More information about HP is available at http://www.hp.com.

Note to editors: More news from HP, including links to RSS feeds, is available at http://www.hp.com/hpinfo/newsroom/.

(1) Dual/Quad Core is a new technology designed to improve performance of certain software products. Not all customers or software applications will necessarily benefit from use of this technology. 64-bit computing on Intel architecture requires a computer system with a processor, chipset, BIOS, operating system, device drivers and applications enabled for Intel 64 architecture. Processors will not operate (including 32-bit operation) without an Intel 64 architecture-enabled BIOS. Performance will vary depending on hardware and software configurations. More information is available at www.intel.com/info/em64t.

(2) Maximum memory capacities assume 64-bit operating systems. Microsoft Windows XP (32-bit) supports 4 GB (with Microsoft 32-bit, the amount of usable memory will be dependent upon system configuration. It may be less than 4 GB); 32-bit Linux can support up to 8 GB.

(3) All specifications represent the typical specifications provided by HPs component manufacturers; actual performance may be higher or lower.

(4) Estimated U.S. list prices. Actual prices may vary.

Intel and Intel Core are trademarks of Intel Corporation in the U.S. and other countries. ENERGY STAR is a registered mark owned by the U.S. government. ATI FireGL is a trademark of AMD. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.

This news release contains forward-looking statements that involve risks, uncertainties and assumptions. If such risks or uncertainties materialize or such assumptions prove incorrect, the results of HP and its consolidated subsidiaries could differ materially from those expressed or implied by such forward-looking statements and assumptions. All statements other than statements of historical fact are statements that could be deemed forward-looking statements, including but not limited to statements of the plans, strategies and objectives of management for future operations; any statements concerning expected development, performance or market share relating to products and services; anticipated operational and financial results; any statements of expectation or belief; and any statements of assumptions underlying any of the foregoing. Risks, uncertainties and assumptions include the execution and performance of contracts by HP and its customers, suppliers and partners; the achievement of expected results; and other risks that are described in HPs Quarterly Report on Form 10-Q for the fiscal quarter ended April 30, 2008 and HPs other filings with the Securities and Exchange Commission, including but not limited to HPs Annual Report on Form 10-K for the fiscal year ended October 31, 2007. HP assumes no obligation and does not intend to update these forward-looking statements.

© 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.



Contact:

HP
Jim Christensen, +1-408-309-0186
Email Contact
Mike Hockey, +1-281-927-9379
Email Contact
or
HP Media Hotline
+1-866-266-7272
Email Contact
www.hp.com/go/newsroom



« Previous Page 1 | 2             

Rating:


Review Article Be the first to review this article
SolidCAM: Program your CNCs directly inside your existing CAD system.


Featured Video
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
Siemens Goes ECAD With Mentor Graphics Acquisition
Jobs
Mechanical Engineer for IDEX Corporation at West Jordan,, UT
Business Partner Manager for Cityworks - Azteca Systems, LLC at Sandy, UT
GIS Analyst II for Air Worldwide at Boston, MA
Senior Structural Engineer for Design Everest at San Francisco, CA
Upcoming Events
Design & Manufacturing, Feb 7 - 9, 2017 Anaheim Convention Center, Anaheim, CA at Anaheim Convention Center Anaheim CA - Feb 7 - 9, 2017
Innorobo 2017 at Docks de Paris Paris France - May 16 - 18, 2017
Display Week 2017 at Los Angeles Convention Center 1201 S Figueroa St Los Angeles CA - May 21 - 26, 2017



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise