Review Article Be the first to review this article
Protomold June Design Tip

Protomold: Rapid Injection Molding
June Design Tip

Good Vibrations — Ultrasonic Welds

There's no shortage of ways to join plastic parts. There are bolts and screws, molded-in clips and snaps, and a variety of adhesives. But for simplicity and permanence, nothing beats sonic welding.

The ultrasonic weld joint is a method for joining two parts. They are designed with a small amount of extra plastic in the area you want to weld. The two parts are placed together and in contact with an ultrasonic generator which causes them to vibrate many thousands of times a second. Friction at the joint liquefies the extra plastic and small adjoining areas on both parts. As the melted material on the mating parts cools, the two parts become essentially one. If you can live with its permanence, Ultrasonic welding is the best of all possible solutions. It eliminates the loose parts and painstaking insertion of threaded connectors. It avoids the geometric complexity of molded-in plastic snaps, and it does away with the chemical problems and mess of adhesives.

The weld is ideal for permanently sealing maintenance-free devices like batteries or assembling a non elastic cup seal to a piston. It is a solution to encapsulating something within plastic when overmolding is not allowable. Sonic welding is also useful for preventing tampering that could void a warranty.

Protomold does not actually perform the sonic welding of parts, but is often called upon to mold parts that will be joined using that process. Weld interfaces have different configurations from simple to complex. Here are three that work well within the Protomold process and Ultrasonic welding in general:

The Shear Joint

The Shear Joint

The Shear joint is a very strong, self-aligning joint that is particularly useful for creating hermetic seals and right-angle joints. It is ideal for crystaline materials such as Nylon, PPS, and PPO, and can also be used with larger parts made of amorphous materials. Note that this joint can leave flash when parts are joined.

The Step Joint

The Step Joint

The Step joint is a stronger, self-aligning joint that provides an excellent appearance. It is suitable for use with amorphous materials.

The Tongue and Groove Joint

The Tongue and Groove Joint

The Tongue and Groove joint eliminates flash caused by the welding process as the weld occurs between two walls and is an excellent choice for hermetic seals. Not recommended for thin walled parts.

Ultrasonic welding design is based on part geometry, including wall thickness and required strength. For more information on designing parts for ultrasonic welding, see:

Joint Design A Critical Factor In Strong Bonds (PDF) from Engineering Design.

The Rule on Joint Design from Sonitek.

Joining of Plastics, Handbook for Designers and Engineers from Hanser Gardner. (Also available through Protomold. Call your sales representative for details.)




The ProtoQuote is new and improved! Try it out today:

Upload your 3D CAD model and we will email to you an informative ProtoQuote.

ProtoQuote Demo:

Still haven't tried the new ProtoQuote 3D Viewer in ProtoQuotes? Give it a try today:

Click here for the demo.

Design Guidelines

As always, you can visit the Protomold Design Guide for helpful Rapid Injection Molding design information.

Protomold Europe

Protomold Europe

European colleagues? Tell them about Protomold Europe!

Plastics Trivia Question

As reported by Scientific American (, biologists at the University College Dublin have discovered that Styrofoam can be broken down by the soil bacteria Pseudomonas putida, if the plastic:

A. is first heated to 520°C in the absence of oxygen.

B. is formulated with a small amount of simple sugar.

C. includes at least 12 percent potato starch.

D. is ground to powder and mixed with whey protein.

E. has been treated with ammonia.

(Honor System: No Googling, Yahooing, or Dogpiling until after you've submitted your guess.)

Last month's question/results:

Which of the following is not true of the plastic Silly Putty:

A. It is a Newtonian fluid.

B. Over 3000 tons have been sold since its introduction.

C. It was originally called Nutty Putty.

D. It is primarily composed of dimethysiloxane.

E. It can be removed from clothing using WD-40.

The correct answer is A. Silly Putty is actually a non-Newtonian Fluid.

The responses are represented in the following chart:

Last  Month's  Results

Upcoming Tradeshows

Want to talk in person? Stop by to discuss your design.

National Manufacturing Week
September 25-27, 2007
Donald E. Stephens
Convention Center
Rosemont, IL
Booth #4128

For more information, visit our Web site at

Get  a  ProtoQuote


Please e-mail suggested topics for future Design Tips, questions for future Designer Surveys, and obscure bits of Plastics Trivia to


IMTS 2018 Register Now>>

Featured Video
Mechanical Engineer for Allen & Shariff Corporation at Pittsburgh, Pennsylvania
Mid-Level Mechanical Engineer for Kiewit at lenexa, Kansas
Upcoming Events
Inside 3D Printing Seoul 2018 at Korea International Exhibition Center (KINTEX), Hall 5 408 Hallyuworld-ro, Ilsanseo-gu, Goyang-si, Gyeonggi-do Goyang Korea (South) - Jun 27 - 29, 2018
AMTEX 2018 at Pragati Maidan New Delhi India - Jul 6 - 9, 2018
34th Annual Coordinate Metrology Society Conference 2018 at Grand Sierra Resort, 2500 East Second Street Meeting & Covention Center Reno NV - Jul 23 - 27, 2018
Kenesto: 30 day trial

Internet Business Systems © 2018 Internet Business Systems, Inc.
25 North 14th Steet, Suite 710, San Jose, CA 95112
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise