Sequence PhysicalStudio Offers Leading S3 Graphics Chip Fastest Available Reduction of Timing and Noise Iterations

Results in Dramatic Improvement in Time-to-Market on a 10 Million+ Gate Graphics Processor Design

SANTA CLARA, Calif.—(BUSINESS WIRE)—Dec. 3, 2004— Sequence Design, the accuracy and performance leader in power integrity tools, announced today that S3 Graphics, a leading graphics solutions company, has benefited from the company's PhysicalStudio(TM) optimization software by reducing timing and noise violations on S3 Graphics' leading graphics processors.

PhysicalStudio concurrently analyzes and optimizes chip timing and signal integrity, before routing in an avoidance mode and after detailed routing in a post-route correction mode, thereby ensuring significant reductions in timing and signal integrity violations.

"When we increased the complexity of our graphics processors, we needed a tool that could handle the timing and signal integrity challenges inherent in higher gate-count designs," said Michael Shiuan, vice president of engineering at S3 Graphics. "Building this complex 130 nanometer, high-frequency, 10 Million+ Gate system-on-a-chip required a state-of-the-art push down flow approach for top level optimization. PhysicalStudio is the best chip- and block- level signal integrity analysis and optimization tool we have used -- the number of timing and noise violations it eliminates is extraordinary!"

According to XinChang, engineering manager at S3 Graphics, "PhysicalStudio's push-down flow allowed the designer to analyze and optimize timing and signal integrity on the full-chip level and generate ECOs that were pushed down to the individual blocks in the design. This unique capability in PhysicalStudio achieved a turnaround in hours, for full-chip timing and signal-integrity closure, something that takes a week to accomplish with competing tools. The ECOs were seamlessly integrated into S3 Graphics' Cadence place & route flow."

PhysicalStudio enabled designers at S3 Graphics to:

-- Recover 17% slack (750ps slack on a 225-MHz design)

-- Fix 1750+ timing violations resulting from crosstalk delay

"A comprehensive power integrity flow is necessary for today's SoC design, beginning at RTL clear through to a tape-out tool like PhysicalStudio that optimizes signal-integrity, power and timing," said Vic Kulkarni, president and CEO, Sequence Design. "We are pleased that S3 Graphics was able to accelerate their design cycle time through the optimization functionality available in PhysicalStudio."

About NanoCool

PhysicalStudio is the optimization stage in Sequence's NanoCool power integrity flow. The flow includes RTL power analysis, voltage-drop analysis and optimization, as well as leakage power reduction. Details may be found at: http://www.sequencedesign.com/2_solutions/NC-DataSheet_New.pdf

Sequence recently launched the NanoCool Low-Power Design seminar series with co-sponsors Artisan Components and Sun Microsystems. Additional inquiries on NanoCool seminars may be directed to seminars@sequencedesign.com.

About PhysicalStudio

PhysicalStudio(TM) is the industry's first design closure tool to predict and correct chip timing, power, and signal integrity issues concurrently, before and after routing. It gives users the ability to interactively optimize hierarchical, multi-million gate SoC designs at the block-level as well as at top-level. PhysicalStudio integrates into popular Cadence, Synopsys and Magma third-party routing tools to enable existing physical flows to reach fast, predictable design closure in silicon geometries below 180 nanometers (nm).

PhysicalStudio Features



-- Post-route correction closes timing faster and at higher clock speeds than other methods

-- Repairs cross-talk delay, glitch, IR drop, and electro-migration failures

-- Analyzes and optimizes timing and signal integrity concurrently

-- Supports both block-level and top-level optimization

-- Large 10M+ gate SoC designs optimized hierarchically

-- Works with existing physical design infrastructure

-- Enables design flows to achieve design closure at 180 nm and below


About S3 Graphics

S3 Graphics Co., Ltd., a VIA Technologies joint venture company, is a leading supplier in the 3D enabled PC graphics market. S3 Graphics ships low power, high performance, commercial grade 3D graphics sub-systems to top tier notebook manufacturers.

S3 Graphics Co., Ltd. has inherited a long tradition of graphics chip excellence from S3 Incorporated, a distinguished pioneer in the development of graphics chip technology. The company continues to break new boundaries in the high quality and power efficient mobile and desktop graphics product sectors.

About Sequence

Sequence Design, Inc. enables system-on-chip designers to bring higher-performance and lower-power integrated circuits quickly to fabrication. Sequence's power and signal integrity software give its more than 130 customers the competitive advantage they need to excel in aggressive technology markets, despite demanding complexity and time-to-market issues of nanometer design.

Sequence has worldwide development and field service operations. The company was recently named by Reed Electronics as one of the top 10 companies to watch in the electronics industry. Sequence is privately held. Sequence is a member of Cadence Design Systems' Connections(TM) and Mentor Graphics' Open Door(TM) partnership programs. Additional information is available at sequencedesign.com.

All trademarks mentioned herein are the property of their respective owners.



Contact:
For Sequence Design, Inc.
Jim Lochmiller, 541-821-3438 

Email Contact

Rating:


Review Article Be the first to review this article
SolidCAM: Program your CNCs directly inside your existing CAD system.


Featured Video
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
Re-Use Your CAD: The ModelCHECK Handbook
Jobs
Business Partner Manager for Cityworks - Azteca Systems, LLC at Sandy, UT
GIS Analyst II for Air Worldwide at Boston, MA
Upcoming Events
Design & Manufacturing, Feb 7 - 9, 2017 Anaheim Convention Center, Anaheim, CA at Anaheim Convention Center Anaheim CA - Feb 7 - 9, 2017
Innorobo 2017 at Docks de Paris Paris France - May 16 - 18, 2017
Display Week 2017 at Los Angeles Convention Center 1201 S Figueroa St Los Angeles CA - May 21 - 26, 2017



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise