Integrating CAE Simulation and FEA to Make Lightweight and Strong Parts

Nov 7, 2014 -- With the growing demand for lightweight designs and composite material applications, part designers and engineers across different industries had been challenged to search for a more innovative yet economic molding solution to stay competitive   while also opening up new opportunities in their  industries. Therefore, the conventional solid injection molding process could no longer satisfy the pressing need to reduce overall production cost while maintaining the competitive advantages for most businesses. Thus, MuCell®process, a novel approach to composite injection molding, was introduced.

In MuCell® process, Supercritical Fluid (SCF), usually as nitrogen (N2 ) or carbon dioxide (CO2), is mixed with polymer melt to create a uniform single-phase solution, and then injected into the mold cavity. The melt flow with bubbles will foam and form a part. The MuCell® Process generally offers a 50-75% improvement in key quality measures, such as flatness, roundness, and warpage, while also eliminating all sink marks. These improvements result from the fact that relatively uniform stress patterns are created in the molded part rather than non-uniform stress characteristics of solid molding. When compared with solid injection molding, MuCell®products rarely have shrinkage problems; the parts that are produced tend to comply far more closely with the mold shape and, presumably, the dimensional specifications of the part itself. In other words, using MuCell® process can help realize the lightweight design concepts with ease without too much compromise on the product mechanical strength.

However, users of MuCell ® process often face a difficult task of trying to find a perfect balance between achieving lightweight products and having sufficient mechanical strength of a finished part. As a result, a substantial amount of mold trials using trial-and-error were needed to attain the most optimized processing set-ups and quality finished parts. In order to alleviate the burden of tedious mold trials and provide further simulation insights into the complex MuCell® process for its users, Moldex3D introduces a new module, Micromechanics Interface to connect with nonlinear multi-scale material modeling software to make the simulation workflow more effective and efficient. Combining with structural analysis, nonlinear multi-scale material modeling software, such as Digimat and Converse, provides the capabilities to simulate the composite materials at micro-macro levels and gives users an opportunity to solve complex nonlinear multi-scale finite element problems. With Moldex3D Micromechanics Interface, users can now output the micromechanics properties of the MuCell® process, such as cell size and cell density, to Digimat and Converse, which previously was not available, for further structural performance assessment of MuCell® parts. Hence, the accuracy of the structural analysis of MuCell ® parts can be further ensured since the microcellular output is considered and incorporated in the structural computation.

In Product Lifecycle Management (PLM), special attention needs to be given to the process-induced properties in the mold-filling analysis in order to get an accurate simulation assessment on product structural analysis. It used to be neglected in the past and it tends to mislead the simulated structure analysis result as the real representation of the final product structural strength.
In reality, the different molding process-induced properties can result in various results of the product structural analyses. In order to help users attain an accurate structural analysis, Moldex3D Micromechanics Interface can successfully connect Moldex3D with nonlinear multi-scale material modeling software like Digimat and Converse. Users can now output the micromechanics properties of MuCell® process, such as cell size and cell density, to Digimat and Converse to attain an accurate structural analysis, thus making PLM more efficient and effective.

Read the complete story ...
Review Article
  • Title is confusing? November 11, 2014
    Reviewed by 'Dennis Nagy'
    The article is interesting, but who chose the title (it's different than the original article at the Moldex website)? FEA is a PART/SUBSET of CAE, according to my experience (40+ years in the CAE business). so CAE cannot be "integrated" with FEA.

      2 of 2 found this review helpful.
      Was this review helpful to you?   (Report this review as inappropriate)

For more discussions, follow this link …

Featured Video
Mid-Level Mechanical Engineer for Kiewit at lenexa, Kansas
Mechanical Engineer for Allen & Shariff Corporation at Pittsburgh, Pennsylvania
System Designer/Engineer for Bluewater at Southfield, Michigan
Geospatial Analyst/Programmer for LANDIQ at Sacramento, California
Software Developer for CHA Consulting, Inc. at Norwell, Massachusetts
GIS Data Analyst for CostQuest Associates, Inc. at Cincinnati, Ohio
Upcoming Events
ESPRIT World 2018 at Indianapolis Marriott Downtown 350 West Maryland Street Indianapolis IN - Jun 11 - 15, 2018
HxGN LIVE 2018 at The Venetian Las Vegas NV - Jun 12 - 15, 2018
IMTS2018 International Manufacturing Tech Show at McCormick Place Chicago IL - Sep 10 - 15, 2018
4th International Conference on Sensors and Electronic Instrumentation Advances (SEIA' 2018) at Movenpick Hotel Amsterdam City Centre Amsterdam Netherlands - Sep 19 - 21, 2018
Kenesto: 30 day trial

Internet Business Systems © 2018 Internet Business Systems, Inc.
25 North 14th Steet, Suite 710, San Jose, CA 95112
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise