EDA Consortium Reports Revenue Increase for Q1 2010

SAN JOSE, CA -- (MARKET WIRE) -- Jul 13, 2010 -- The EDA Consortium (EDAC) Market Statistics Service (MSS) today announced that the Electronic Design Automation (EDA) industry revenue for Q1 2010 was $1247 million, a 4.6 percent increase compared to $1192.1 million in Q1 2009. Sequential EDA revenue declined 1.2 percent, while over the last four quarters it declined 5.9 percent.

"Led by increases in the CAE and Semiconductor IP categories, the EDAC revenue numbers show an increase over Q1 2009," said Wally Rhines, EDAC chair and chairman and CEO of Mentor Graphics. "Geographically, the Asia/Pacific region showed growth both year to year and quarter over quarter."

Companies that were tracked employed 26,099 professionals in Q1 2010, up 0.4 percent compared to Q4 2009, but down 1.7 percent from the 26,561employed in Q1 2009.

The complete MSS report, containing detailed revenue information broken out by both categories and geographic regions, is available via subscription from the EDA Consortium.

Revenue by Product Category
Computer Aided Engineering (CAE), EDA's largest category, generated revenue of $458.5 million in Q1 2010. This represents a 7.2 percent increase over the same period in 2009. Over the last four quarters, CAE declined 3.5 percent.

IC Physical Design & Verification revenue decreased to $274.4 million in Q1 2010, a 9.2 percent decrease compared to Q1 2009. Over the last four quarters, IC Physical Design & Verification declined 8.3 percent.

Printed Circuit Board and Multi-Chip Module (PCB & MCM) revenue decreased 8.8 percent compared to Q1 2009, to $109.4 million. Over the last four quarters, PCB & MCM decreased 8.9 percent.

Semiconductor Intellectual Property (SIP) revenue totaled $320.9 million in Q1 2010, a 35.8 percent increase compared to Q1 2009. Over the last four quarters, SIP decreased 0.1 percent.

Services revenue was $83.7 million in Q1 2010, a decrease of 20.7 percent compared to Q1 2009. Over the last four quarters, services decreased 21.7 percent.

Revenue by Consuming Region
The Americas, EDA's largest region, purchased $492.9 million of EDA products and services in Q1 2010, representing a decrease of 0.2 percent compared to Q1 2009. Over the last four quarters, the Americas were down 5.5 percent.

Revenue in Europe, the Middle East, and Africa (EMEA) was up 0.5 percent in Q1 2010 compared to Q1 2009 on revenues of $224.2 million. Over the last four quarters, EMEA was down 13.1 percent.

First quarter 2010 revenue from Japan decreased 1.9 percent to $250.8 million compared to Q1 2009. Over the last four quarters, Japan decreased 9.1 percent.

The Asia/Pacific (APAC) region increased to $279.0 million in Q1 2010, a 33.2 percent increase compared to the same quarter in 2009. Over the last four quarters, APAC increased 7.0 percent.

About the MSS Report
The EDA Consortium Market Statistics Service reports EDA industry revenue data quarterly and is available by annual subscription. Both public and private companies contribute data to the report. Each quarterly report is published approximately three months after quarter close. MSS report data is segmented as follows: revenue type (product licenses and maintenance, services, and SIP), application (CAE, PCB/MCM Layout, and IC Physical Design and Verification), and region (the Americas, Europe Middle East and Africa, Japan, and Asia Pacific), with many subcategories of detail provided. The report also tracks total employment of the reporting companies.

About the EDA Consortium
The EDA Consortium is the international association of companies that provide design tools and services that enable engineers to create the world's electronic products used for communications, computer, space technology, medical, automotive, industrial equipment, and consumer electronics markets among others. For more information about the EDA Consortium, visit www.edac.org, or to subscribe to the Market Statistics Service, call (408) 287-3322 or email Email Contact.

The information supplied by the EDA Consortium is believed to be accurate and reliable, but the EDA Consortium assumes no responsibility for any errors that may appear in this document. All trademarks and registered trademarks are the property of their respective owners.

Press Contacts: 
Paul Cohen
EDA Consortium
408-287-3322

Suzanne Graham
Mentor Graphics
503-685-7789 





Review Article Be the first to review this article

SolidCAM - See it Live

Featured Video
Jobs
MECHANICAL ENGINEER for VEi Global, Inc. at Fargo, North Dakota
Field Sales Engineer - Instruments and Valves for Miller Mechanical Specialties at Mendota Heights, Minnesota
Mechanical Engineer with Mobile Equipment Experience for Specsys inc at Montevideo, Minnesota
Senior Engineer for Specsys inc at Montevideo, Minnesota
Water Quality Analyst for City of Arvada at Arvada, Colorado
QA Engineer for Cosential at Austin, Texas
Upcoming Events
The NAMM Show 2019 at Anaheim Convention Center Anaheim CA - Jan 24 - 27, 2019
Design & Manufacturing 2019 at Anaheim Convention Center Anaheim CA - Feb 5 - 7, 2019
SOLIDWORKS World 2019 at Dallas TX - Feb 10 - 13, 2019
The MFG Meeting 2019 at JW Marriot Starr Pass Hotel & Spa Tucson AZ - Mar 6 - 9, 2019
Kenesto: 30 day trial
MasterCAM



Internet Business Systems © 2019 Internet Business Systems, Inc.
25 North 14th Steet, Suite 710, San Jose, CA 95112
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise