New VCE6467 Video Communications Engine integrates Texas Instruments hardware and RADVISION software on a single chip for a variety of two-way HD video communications

Cost-effective, complete hardware + software solution provides 10 times reduction in number of integration man hours, allowing for faster time to market

DALLAS, June 1 — (PRNewswire) — Video communications designers can now benefit from an integrated video communications solution – pre-installed software on a video processor chip, available from a single vendor.  The VCE6467 Video Communications Engine from Texas Instruments Incorporated (TI) (NYSE: TXN) and RADVISION's Technology Business Unit (TBU) is a cost-conscious solution easily enabling a variety of two-way, live HD video communications applications, including video conferencing, telemedicine, digital signage and set-top boxes.  This inclusive solution reduces software integration time by more than 10 times the number of man hours normally required, which significantly speeds time to market.

Based on the DaVinci™ DM6467 video processor from TI, the VCE6467 comes pre-loaded with RADVISION's video communications software and allows HD video at 720p 30 frames per second (fps) using H.264 encoding and decoding for seamless two-way communication with low-latency.  Because the VCE6467 provides HD video, reduced latency and real-time communication, the end video applications allow realistic, nearly face-to-face communications, which eliminates the need for in-person meetings and helps save time and money on unnecessary travel. www.ti.com/vce6467prlp.

VCE6467 key features and benefits:


Key Features

Benefits

720p 30 fps H.264 video with G.711 audio with audio visual synchronization

Allows live, two-way video communications with low latency

Optional multi-protocol support (SIP, H.323)

Ability to communicate and interoperable with both SIP and H.323 devices

Media quality framework (SVC, bandwidth management, packet loss resilience)

Enables the ability to deploy product over any network, including public internet


Optional fully interoperable with all major video conferencing systems

Communicates with any video communication device available on the market




Software and support

Helping make development easier, the VCE6467 will be accompanied by documentation, software examples, training and support for customization and integration.  

Pricing and availability:

Customers can begin designing by downloading the VCE6467 trial software for use on the DM6467T EVM, available for $1,995 USD.  The VCE6467 will be widely available in 3Q 2010 www.ti.com/vce6467prlp.

.  

About Texas Instruments

Texas Instruments (NYSE: TXN) helps customers solve problems and develop new electronics that make the world smarter, healthier, safer, greener and more fun. A global semiconductor company, TI innovates through design, sales and manufacturing operations in more than 30 countries.  For more information, go to www.ti.com.

About RADVISION

RADVISION (Nasdaq: RVSN) is the industry's leading provider of market-proven products and technologies for unified visual communications over IP, 3G and IMS networks. With its complete set of standards-based video networking infrastructure and developer toolkits for voice, video, data and wireless communications, RADVISION is driving the unified communications evolution by combining the power of video, voice, data and wireless – for high definition video conferencing systems, innovative converged mobile services, and highly scalable video-enabled desktop platforms on IP, 3G and emerging next-generation IMS networks. To gain additional insights into our products, technology and opinions, visit community.radvision.com and blog.radvision.com. For more information about RADVISION, visit www.radvision.com.

This press release contains forward-looking statements that are subject to risks and uncertainties. Factors that could cause actual results to differ materially from these forward-looking statements include, but are not limited to, general business conditions in the industry, changes in demand for products, the timing and amount or cancellation of orders and other risks detailed from time to time in RADVISION's filings with the Securities Exchange Commission, including RADVISION's Form 20-F Annual Report. These documents contain and identify other important factors that could cause actual results to differ materially from those contained in our projections or forward-looking statements. Stockholders and other readers are cautioned not to place undue reliance on these forward-looking statements, which speak only as of the date on which they are made. We undertake no obligation to update publicly or revise any forward-looking statement.

Trademarks

DaVinci™ is a trademark of Texas Instruments.  All other trademarks and registered trademarks belong to their respective owners.

SOURCE Texas Instruments

Contact:
Texas Instruments
Christi Davidson of GolinHarris
Phone: +1-972-341-2584
Email Contact
Gem-Ann Reagan of Texas Instruments
Phone: +1-214-567-0795, gem- Email Contact
Adi Sfadia, Chief Financial Officer of RADVISION
Phone: +1-201-689-6340
Email Contact
media relations, Paul Macchia of Dukas Public Relations
Phone: +1-212-704-7385
Email Contact
investor relations, June Filingeri of Comm-Partners LLC
Phone: +1-203-972-0186
Email Contact
Web: http://www.ti.com




Review Article Be the first to review this article
HP

Autodesk - DelCAM

Featured Video
Jobs
CAD Systems Administrator for KLA-Tencor at Milpitas, CA
Senior Mechanical Engineer for Verb Surgical at Mountain View, CA
Principal Research Mechatronics Engineer for Verb Surgical at Mountain View, CA
Industrial Designer Intern – Spring 2017 for Nvidia at Santa Clara, CA
Lead Geospatial Analyst for Alion at McLean, VA
Upcoming Events
SOLIDWORKS 2017 Launch Event – Walsall at Village Hotel Club, Walsall, WS2 8TJ Walsall United Kingdom - Mar 30, 2017
PI APPAREL Hong Kong 2017 at SHANGRI-LA KOWLOON 64 Mody Road Tsim Sha Tsui East Kowloon Hong Kong - Apr 5 - 6, 2017
SOLIDWORKS intro and hands on session – Slough at Baylis House, Slough, Berkshire, SL1 3PB Slough United Kingdom - Apr 7, 2017
Engineer 3D! Training + Technology Conference at Hyatt Regency Milwaukee 333 West Kilbourn Avenue Milwaukee WI - Apr 25 - 26, 2017
MasterCAM



Internet Business Systems © 2017 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise