Agilent Technologies’ New LTE Applications Target 4G System-Level Designers

IP, Digital Pre-distortion and MIMO Channel Products Accelerate eNodeB, User Equipment Design

SANTA CLARA, Calif. — (BUSINESS WIRE) — February 16, 2010 — Agilent Technologies Inc. (NYSE: A) today introduced a new line of system-level design and verification products for 3GPP LTE physical layer (PHY) design at Mobile World Congress 2010. In addition to its traditional test and measurement products, Agilent now provides predictive products and algorithmic references for the SystemVue platform that are consistent with the LTE v.8.9.0 (December 2009) standard. The new line includes four products that accelerate 4G deployment for LTE system architects, baseband hardware designers, and RF equipment by bringing new levels of realism into the architecture and modeling stages.

While 4G networks promise dramatic improvements in data throughput and spectral efficiency, the complexity of the evolving 3GPP LTE standard has forced many system architects to reconsider their use of general-purpose toolsets. By cutting across a variety of domains (such as signal processing and mathematics, baseband hardware design, RF/analog design and measurements), Agilent’s new 4G products are able to provide system architects with the focused application support for LTE v.8.9.0 that they demand. Agilent’s 4G products streamline verification and bring measurement-level realism into the creative process. The result is higher-performance Layer 1 architectures and algorithms resulting in earlier design maturity and the need for less design margin.

The four new products being introduced by Agilent at Mobile World Congress 2010 include:

W1715 MIMO Channel Builder:

The W1715 MIMO Channel Builder is a simulation blockset for LTE architecture and receiver designers, based on the WINNER and WINNER-II fading algorithms. By incorporating non-ideal MIMO antenna performance (e.g., crosstalk and directionality), the W1715 goes beyond these standard propagation models. It enables 2D far-field data to be imported from antenna measurements or 3D EM simulations, including Agilent EM PRO. Realistic antenna degradations allow accurate assessments of link-level LTE architectures and receiver algorithms to be made at a very early stage, before prototypes have been committed for the mechanical, RF/antenna, or baseband/DSP designs. Previously, interactions between these domains required a fully operational hardware radio and came much later in the design process, possibly during drive test. The W1715 brings some of this drive-test realism into the algorithm phase of the design, accelerating design maturity and performance.

The W1715 also follows the design into hardware test. The same Agilent SystemVue simulation modules are used to generate test vectors for download into multi-channel Agilent signal generators (e.g., the N5106A PXB) or interoperate with the 89601 VSA software. The W1715 offers an economical alternative to real-time hardware faders, since SystemVue can be shared on a computer network and used throughout the design process by distributed teams. Agilent’s integration of design and test platforms across the LTE design cycle maximizes re-use of assets, minimizes engineering effort, and produces consistent results.

W1716 Digital Pre-Distortion (DPD) Software

The W1716 Digital Pre-Distortion builder helps LTE system integrators, RF component designers, and baseband architects quickly transition from 3G to 4G by creating baseband signal processing networks that improve the range of analog power amplifiers and transceiver ICs, improve efficiency, and extend battery life. The W1716 also quickly assesses the suitability of existing 3G designs for 4G applications. Such capabilities translate into savings for both design effort and component cost.

The W1716 consists of a wizard-based UI that automatically models and corrects common sources of memory effects, in-band EVM degradation and adjacent-channel power re-growth. The software controls signal generators and analyzers to characterize the component response to a configurable LTE signal. The W1716 produces two networks: an impaired dataflow simulation model to use at the link level, and a baseband pre-distortion network to correct for those impairments. After extraction, the W1716 completes a report documenting the actual DPD improvement it achieved, using authentic LTE v.8.9.0 waveforms, or any user-defined waveform that can be made with SystemVue.

“We identified a gap between today’s proprietary 3G DPD solutions and the market’s need for an inexpensive, open, technology-neutral platform for 4G,” said Jian Yang, ESL integrating manager at Agilent Technologies. “The new W1716 software addresses this gap. It is producing 20-dB ACP improvements on the bench, on real LTE waveforms. What used to take months in a high-end lab now takes minutes, thanks to this new technology and guided UI.”

W1910/2 LTE Baseband Verification Library Reference Blockset

Agilent’s W1910 LTE Baseband Verification Library reference blockset has been updated to LTE v.8.9.0 and now includes expanded PRACH and HARQ support. The HARQ simulation support uses a unique dynamic dataflow simulation mode. This mode allows the symbol rate to change dynamically over the course of the simulation while retaining the timing and carrier information necessary for full RF effects, frequency-dependent phase noise, and channel fading. This capability reduces LTE simulations to minutes or hours for meaningful throughput, and BLER and EVM compliance measurements. Additionally, the updated W1910 keeps pace with changes to the Agilent Signal Studio and VSA software to maintain interoperability with Agilent measurement solutions.

1 | 2  Next Page »



Review Article Be the first to review this article

Featured Video
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
Re-Use Your CAD: The ModelCHECK Handbook
Jobs
Mechanical Engineer for IDEX Corporation at West Jordan,, UT
GIS Analyst II for Air Worldwide at Boston, MA
Senior Structural Engineer for Design Everest at San Francisco, CA
Business Partner Manager for Cityworks - Azteca Systems, LLC at Sandy, UT
Upcoming Events
Design & Manufacturing, Feb 7 - 9, 2017 Anaheim Convention Center, Anaheim, CA at Anaheim Convention Center Anaheim CA - Feb 7 - 9, 2017
Innorobo 2017 at Docks de Paris Paris France - May 16 - 18, 2017
Display Week 2017 at Los Angeles Convention Center 1201 S Figueroa St Los Angeles CA - May 21 - 26, 2017



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise