Mentor Graphics Delivers Hardware-Assisted Solution for the Accelerated Verification of USB 2.0 Products

WILSONVILLE, Ore. — (BUSINESS WIRE) — January 14, 2010 — Mentor Graphics Corp. (NASDAQ: MENT), the leader in high-performance system verification solutions, today announced a hardware-assisted solution to accelerate the verification of Universal Serial Bus (USB) 2.0 products, including hard disk drives and other mass storage devices. This new solution enables designers to test the System-on-Chip (SoC) design that controls a hard disk drive or similar mass storage device, by providing an accurate, hardware-based model of the real disk drive connected to their SoC.

This iSolveTM USB Peripheral product has a ‘plug-and-play’ interface to the Veloce® family of hardware-assisted emulators, providing a cost-effective and efficient solution to verify USB designs. The new product adds to the existing iSolve family of solutions for the accelerated verification of applications such as multimedia, networking, embedded systems, wireless, and storage devices.

USB is a pervasive technology across a wide range of products, with billions of devices having been created that use the protocol. With the ever-increasing demand for system-level verification of such products, a heavy burden is placed on SoC designers who need to verify how their designs interact with the USB devices connected to them.

“New consumer products, in particular, are increasingly dependent on the use of the latest-generation USB devices, and design engineers are concerned with the quick and efficient verification of their SoC designs that will connect to these devices,” said Jim Kenney, director of marketing, Mentor’s Emulation Division. “We took a new approach to solve these challenges with our iSolve USB Peripheral product, by providing a flexible, easy-to-use, and highly-configurable USB peripheral device model. This gives our customers the ability to verify multiple configurations and descriptions of USB peripheral devices—all with the same emulator solution—rather than needing many specific devices.”

Combined with the Veloce emulation family, the iSolve USB Peripheral product delivers a high-performance and easy-to-use system verification environment to develop new SoCs containing a USB host controller, without compromising delivery schedules. The solution offers several key benefits:

  • Easy-to-use configuration tool means users are able to parameterize their USB mass storage device quickly and start their SoC verification as soon as possible
  • Productive debug environment provides access to low-level transactions to detect those hard-to-find bugs
  • High-speed data accesses allows loading or unloading of GBytes of data in minutes rather than hours.
  • Compliant to USB 2.0 standard

The iSolve USB Peripheral solution can be used with traditional in-circuit emulation (ICE) as well as a high-performance, transaction-based acceleration mode of operation. The ability to mix and match traditional ICE capabilities with high-performance transaction-based acceleration facilitates the smooth transition from a simulation-centric use model to in-circuit emulation. The solution is available for deployment at customer sites effective immediately.

For product information, contact your Mentor Graphics sales representative, call 1-800-547-3000, or visit the website at www.mentor.com/med.

About Mentor Graphics

Mentor Graphics Corporation (NASDAQ: MENT) is a world leader in electronic hardware and software design solutions, providing products, consulting services and award-winning support for the world’s most successful electronics and semiconductor companies. Established in 1981, the company reported revenues over the last 12 months of about $800 million and employs approximately 4,425 people worldwide. Corporate headquarters are located at 8005 S.W. Boeckman Road, Wilsonville, Oregon 97070-7777. World Wide Web site: http://www.mentor.com/.

(Mentor Graphics and Veloce are registered trademarks and iSolve is a trademark of Mentor Graphics Corporation. All other company and/or product names are the trademarks and/or registered trademarks of their respective owners.)

 

 



Contact:

Mentor Graphics
Carole Dunn, 503-685-4716
Email Contact
or
Suzanne Graham
Mentor Graphics, 503-685-7789
Email Contact

 




Review Article Be the first to review this article
SolidCAM: Program your CNCs directly inside your existing CAD system.


Featured Video
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
Re-Use Your CAD: The ModelCHECK Handbook
Jobs
GIS Analyst II for Air Worldwide at Boston, MA
Business Partner Manager for Cityworks - Azteca Systems, LLC at Sandy, UT
Upcoming Events
Design & Manufacturing, Feb 7 - 9, 2017 Anaheim Convention Center, Anaheim, CA at Anaheim Convention Center Anaheim CA - Feb 7 - 9, 2017
Innorobo 2017 at Docks de Paris Paris France - May 16 - 18, 2017
Display Week 2017 at Los Angeles Convention Center 1201 S Figueroa St Los Angeles CA - May 21 - 26, 2017



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise