Mentor Graphics and Applied Materials Deploy OASIS.MASK Open Data Standard for Higher Efficiency Mask Manufacturing

WILSONVILLE, Ore. & SANTA CLARA, Calif. — (BUSINESS WIRE) — September 14, 2009 — Mentor Graphics Corporation (NASDAQ: MENT) and Applied Materials, Inc. (NASDAQ: AMAT) today announced an important milestone in the adoption of open data formats for mask manufacturing. The first volume production deployment of the new OASIS.MASK (SEMI standard P44) format was performed on Applied’s Aera2™ advanced mask inspection systems using Mentor Graphics’ mask data preparation software technology. The new format greatly simplifies the task of creating the complex, high fidelity photomasks that are vital to fabricating semiconductor devices at 32nm and below technology nodes.

OASIS.MASK (Open Artwork System Interchange Standard for Photomasks) is an open standard interchange format used to represent and express chip level physical and mask layout data. The OASIS.MASK format reduces the size of mask data files by approximately one-half, eliminating the file transfer bottleneck between software tools and mask manufacturing equipment – a key benefit with today’s near-terabyte file sizes. As an open interface, it enables the same data file to be used for pattern generation, metrology and inspection, simplifying mask manufacturing process flows by eliminating complex format conversion steps.

“We are working with Mentor Graphics, a leader in the adoption of OASIS standards, to improve efficiency up and down the mask-making value chain by encouraging the adoption of open standards,” said Tom St. Dennis, senior vice president and general manager of Applied’s Silicon Systems Group. “By incorporating the OASIS.MASK format in our Aera2 systems, we can continue to provide the most competitive, high throughput, die-to-database inspection solutions for our most advanced customers.”

“Applied Materials’ decision to implement OASIS.MASK in their products shows the value of OASIS mask data format,” said Joseph Sawicki, vice president and general manager for the Design-to-Silicon division at Mentor Graphics. “Mentor’s experience with OASIS goes back to the development of the original OASIS format (SEMI standard P39), so incorporating our technology into Aera2 was a logical extension of our product efforts. The use of OASIS.MASK for mask manufacturing is fully supported by the Calibre® platform in the Calibre FRACTUREv™, Calibre MDPverify™, and Calibre MDPview™ products, which are all available today.”

Applied and Mentor will showcase their pioneering deployment of OASIS.MASK in a production environment at SPIE Photomask 2009, the mask-making industry’s premier technical symposium, to be held September 14-17 in Monterey, California.

Applied Materials, Inc. (NASDAQ: AMAT) is the global leader in Nanomanufacturing Technology™ solutions with a broad portfolio of innovative equipment, service and software products for the fabrication of semiconductor chips, flat panel displays, solar photovoltaic cells, flexible electronics and energy efficient glass. At Applied Materials, we apply Nanomanufacturing Technology to improve the way people live. Learn more at www.appliedmaterials.com.

Mentor Graphics Corporation (NASDAQ: MENT) is a world leader in electronic hardware and software design solutions, providing products, consulting services and award-winning support for the world’s most successful electronics and semiconductor companies. Established in 1981, the company reported revenues over the last 12 months of about $800 million and employs approximately 4,425 people worldwide. Corporate headquarters are located at 8005 S.W. Boeckman Road, Wilsonville, Oregon 97070-7777. World Wide Web site: http://www.mentor.com/.

(Mentor Graphics and Calibre are registered trademarks and FRACTUREv, MDPview and MDPverify are trademarks of Mentor Graphics Corporation. Applied Materials is a registered trademark and Aera2 is a trademark of Applied Materials. All other company or product names are the registered trademarks or trademarks of their respective owners.)

Photos/Multimedia Gallery Available: http://www.businesswire.com/cgi-bin/mmg.cgi?eid=6048723&lang=en



Contact:

Mentor Graphics
Gene Forte, 503-685-1193
Email Contact
Sonia Harrison, 503-685-1165
Email Contact
or
Applied Materials
Betty Newboe, 408-563-0647 (editorial/media)
Email Contact
Michael Sullivan, 408-986-7977 (financial community)
Email Contact




Review Article Be the first to review this article

Autodesk University 2017

Featured Video
MCAD Corporate Newsletter
rss feed
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
NVIDIA’s AI Computer Drives AVs
Jobs
Senior Mechanical Engineer for Albert Kahn and Associates at Detroit, MI
Mechanical Engineer for The Planate Management Group LLC at Perry Point, MD
Structural Engineer for The Planate Management Group LLC at Perry Point, MD
GIS Analyst for G2 Partners LLC at San Ramon, CA
Structural Engineer for Albert Kahn and Associates at Detroit, MI
Upcoming Events
ASSESS 2017 CONGRESS at Bolger Center Potomac MD - Nov 1 - 3, 2017
FABTECH 2017 at McCormick Place Chicago IL - Nov 6 - 9, 2017
ATX MINNEAPOLIS 2017 at Minneapolis MN - Nov 8 - 9, 2017
2017 China Chongqing International Machine Tool Show (CCIMT) at Chongqing International Expo Center, Yubei Chongqing China - Nov 13 - 16, 2017



Internet Business Systems © 2017 Internet Business Systems, Inc.
25 North 14th Steet, Suite 710, San Jose, CA 95112
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise