World’s First Micro SCARA Robot Premieres at International Robotics Show

CARLSBAD, Calif., Nov. 11, 2015 (GLOBE NEWSWIRE) -- At the International Robotics Show (IREX) in Tokyo, Japan, SMAC Moving Coil Actuators will introduce a prototype version of the world's first five axes, direct drive micro SCARA robot. The micro SCARA robot is an evolution of SMAC’s robotic finger, adding two additional axes that emulate a wrist. SMAC expects an early 2016 release.

The SMAC robotic finger was introduced earlier this year in Chicago, Illinois, and Hannover, Germany. The 25mm motor used in the front joint (PIP) is a servo "partial" motor and equipped with an SMAC rotary encoder with 15.5K counts per revolution. It achieves a high torque/diameter ratio due to the proprietary magnetic circuit design as well as the coil design. Intellectual property rights have been addressed.

Another - larger motor (35MM) acts as the 2nd joint (MCP FLex). It puts out a torque of 630 mNm and thus can exert a resultant force of 7N at the tip. Both motors move  +/- 45 degrees - as the human joints do.

The 3rd motor operates as the first joint (MCP Abd).  This is the joint that moves side to side. This motion is based on SMAC’s moving coil linear design and already meets the required parameters.

These motors have been integrated into a structure that allows them to operate and cover the same movement capability as a human’s finger. The structure weighs approximately 350 grams and is physically about 1.5 x larger than the average male finger.

The Micro SCARA Robot (MSR) incorporates SMAC's patented Soft-Land technology to handle fragile components. The ability to softly land on a surface means the MSR virtually instantly (in milliseconds) recognizes that contact has been made and at what distance. This duplicates the action of a human finger and results in a test of the various finger interfaces that is very close to the finger action it is testing for.

Both the SMAC robotic finger and micro SCARA robot will next be presented live to the public by SMAC R&D Specialist, Naoyuki Okada, at Workshop Venue A (East 1 Hall Entrance), December 2, 2015, 2:30pm to 3:30pm. It can be seen throughout the International Robotics Exhibition at Booth # IR3-34.

 

Contact:
John Miewald, Marketing Manager
SMAC Moving Coil Actuators
760-929-7575
www.smac-mca.com

Primary Logo




Review Article Be the first to review this article
SolidCAM: Program your CNCs directly inside your existing CAD system.


Featured Video
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
Siemens Goes ECAD With Mentor Graphics Acquisition
Jobs
Mechanical Engineer for IDEX Corporation at West Jordan,, UT
GIS Analyst II for Air Worldwide at Boston, MA
Senior Structural Engineer for Design Everest at San Francisco, CA
Business Partner Manager for Cityworks - Azteca Systems, LLC at Sandy, UT
Upcoming Events
Design & Manufacturing, Feb 7 - 9, 2017 Anaheim Convention Center, Anaheim, CA at Anaheim Convention Center Anaheim CA - Feb 7 - 9, 2017
Innorobo 2017 at Docks de Paris Paris France - May 16 - 18, 2017
Display Week 2017 at Los Angeles Convention Center 1201 S Figueroa St Los Angeles CA - May 21 - 26, 2017



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise