DINI Group Verifies Compatibility of Northwest Logic’s PCI Express Cores with Virtex-7 ASIC Prototyping Platforms

April 29, 2014 – Northwest Logic and DINI Group announced today that Northwest Logic’s PCI Express® (PCIe®) 3.0 solution, including the Expresso 3.0 Core (PCI Express 3.0 Controller Core) has been validated on DINI Group’s 1, 2, and 4-FPGA ASIC prototyping platforms. This validation was done with 4 lanes running at 5 Gbit/s SERDES rates.

“DINI Group continues to use a variety of Northwest Logic cores to validate our ASIC prototyping platforms.” said Brian Poladian, Senior Engineer at Dini Group, “Northwest Logic provides proven, high-performance solutions that integrate effortlessly into our platforms.  We know that when we use IP from Northwest Logic we’ll be able to focus our efforts on prototyping the design rather than wasting time with someone else’s buggy IP.”

DINI Group is the market leader in FPGA-based ASIC prototyping hardware and is currently shipping ASIC prototyping platforms based on Xilinx and Altera FPGAs. The highlight of current generation is the Xilinx Virtex7-based DNV7F4A, which contains four 7V2000T FPGAs.  This revolutionary stacked-silicon FPGA is the largest shipping today and dramatically eases the difficult task of logic partitioning. The DNV7F4A is capable of prototyping 56 million ASIC gates.  It can also be seamlessly stacked 4 times to support ASIC gate counts in excess of 200 million.

“DINI Group’s FPGA platforms which support 10s of millions of ASIC gates enable developers to effectively prototype large ASIC designs.” said Northwest Logic’s president, Brian Daellenbach. “We are pleased that DINI Group trusts and continues to use our IP to help validate their platforms.   This pre-validation ensures that developers will be able to migrate their PCI Express based designs to these platforms quickly and effectively.”

Northwest Logic provides a complete PCI Express Solution. This solution includes Northwest Logic’s high-performance, easy-to-use, silicon-proven Expresso 3.0/2.1/1.1 Cores for PCI Express, DMA Back-End Core which provides high-performance scatter-gather DMA engines, Drivers (Linux & Windows) and Application software. For a complete system design Northwest Logic optionally provides its high-performance DDR4/3/DDR2/1, LPDDR4/3/2/1 SDRAM and HBM, MRAM, RLDRAM 3/11 Memory Controller Cores and add‐on cores (AXI/AHB, Multi-Port, Reorder, etc.). These solutions are available separately or as a single, fully integrated solution.

About DINI Group

DINI Group is an established leader in large, FPGA-based boards, critical IP, and systems. DINI Group FPGA boards are used in large quantities for ASIC and SOC prototyping, low-latency trading, and high performance computing. From their corporate campus in La Jolla, California, DINI Group employees have supplied over twelve billion ASIC gates.

About Northwest Logic

Northwest Logic, founded in 1995 and located in Beaverton, Oregon, provides high-performance, silicon-proven, easy-to-use IP cores including high-performance PCI Express solution (PCI Express 3.0, 2.1 and 1.1 cores and drivers), Memory Interface Solution (DDR4/3/2, LPDDR4/3/2 SDRAM; HBM, MRAM, RLDRAM 3/II), and MIPI Solution (CSI-2, DSI). These solutions support a full range of platforms including ASICs, Structured ASICs and FPGAs. For additional information, visit www.nwlogic.com.

Media Contacts:                      

                                                DINI Group                               

                                                Mike Dini
                                                mdini@dinigroup.com
                                                 www.dinigroup.com
                                                (858) 454-3419 x11 

                                                Northwest Logic, Inc
                                                Vinitha Seevaratnam
                                                 www.nwlogic.com
                                                (503) 533-5800 x308

 




Review Article Be the first to review this article

Featured Video
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
Siemens Goes ECAD With Mentor Graphics Acquisition
Jobs
Mechanical Engineer for IDEX Corporation at West Jordan,, UT
Senior Structural Engineer for Design Everest at San Francisco, CA
Business Partner Manager for Cityworks - Azteca Systems, LLC at Sandy, UT
GIS Analyst II for Air Worldwide at Boston, MA
Upcoming Events
Design & Manufacturing, Feb 7 - 9, 2017 Anaheim Convention Center, Anaheim, CA at Anaheim Convention Center Anaheim CA - Feb 7 - 9, 2017
Innorobo 2017 at Docks de Paris Paris France - May 16 - 18, 2017
Display Week 2017 at Los Angeles Convention Center 1201 S Figueroa St Los Angeles CA - May 21 - 26, 2017
SolidCAM: Program your CNCs directly inside your existing CAD system.



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise