Solido Announces High-Sigma Monte Carlo Meta-Simulator Achieves high yield, high performance memory design

SAN JOSE, Calif. April 24, 2012 - Solido Design Automation Inc., a leading provider of analysis and design software for high yield and performance IP and system-on-chip (SoCs), formally announced today its High-Sigma Monte Carlo (HSMC) meta-simulator solution.  Solido’s HSMC, part of the Variation Designer product family, was released in October 2010 and is in use at 7 of the top 20 semiconductor vendors.  It provides accurate, scalable and verifiable analysis and design solutions for memory chips, and is 100x+ faster than Monte Carlo analysis.

Memory Market Drivers

Driven by the higher level of integration demanded for mobile devices, memory IP is an integral part of SoC design, and requires low power, minimum cost and die area, and maximum performance at high yield. As a result, memory designers are early adopters of state-of-the-art foundry processes (28 nm and below). The increased variability associated with these new processes leads to increased risks in yield while meeting aggressive power, performance and area goals.

Many memory elements, such as bit cells and sense amps, are replicated in large arrays so that producing a single working product requires that the millions of repeated cells all work correctly, without failure. This makes high yield design a requirement; by definition, 5 sigma has only one failure in two million, and 6 sigma has only one failure in a billion.  The number of simulations required to validate high yield using traditional methods is simply infeasible, even with today’s fastest simulators, and even while utilizing massive compute clusters and cloud computing. 

Meta-simulation

There is a continuing progression of electronic design automation tools to manage increased complexity through greater abstraction and partitioning methods. Meta-simulators are part of this trend. A meta-simulator feels like using a single simulator to the designer, yet drives hundreds or thousands of simulations in parallel from traditional simulation engines.  Meta-simulators offer a “meta-level” analysis that may utilize a large number of simulations, while keeping the user input to not much more than a netlist. The output is simple, numerical, and well-defined, just like the result of a simulation.  

Meta-simulation has historically been limited to simplistic methods, such as running corners or running Monte Carlo. Today, meta-simulation techniques can be much more powerful, addressing designer challenges and speeding up different analyses types in precisely-targeted ways.  For example, rather than running 100 or 10,000 PVT corners just to search for the worst cases, a “Fast PVT” meta-simulator would analyze all the PVT corners and intelligently simulate only the small subset requires to identify the worst-case corners with confidence. 

 Meta-simulation goes beyond distributed processing; it also adds efficiency to high-value analysis capabilities such as: fast PVT analysis; fast extraction of statistical corners; and fast sensitivity analysis.   An ideal meta-simulator for memory design measures yield-performance tradeoffs out to 5 and 6 sigma, with the same accuracy as millions or billions of Monte Carlo simulations, but with 100x+ fewer simulations. 

Solido’s High-Sigma Monte Carlo Key Features

Solido High-Sigma Monte Carlo meta-simulator provides rapid analysis of yield-performance tradeoffs for memory design. Some of its key features:

1. Achieves high-sigma memory verification in thousands rather than millions or billions of simulations.  It analyzes the billions of Monte Carlo samples, and then focuses its SPICE simulation resources to find rare failures or validating the target yield. 

2. Runs fast enough to facilitate both iterative design and verification within production timelines, enabling yield-performance tradeoffs. A Solido HSMC 5 billion Monte Carlo sample run can take as little as 15 minutes.

3. Provides SPICE-accurate information in the extreme tails of the high-sigma distribution, where defects are expected to occur. Is applicable to production-scale high-sigma designs with hundreds of process variables. 

4. Interfaces to all the leading SPICE simulators used by memory designers. Runs at the command-line, just like a single simulation, while supporting parallelization to hundreds of cores/machines, managing multiple simulations through LSF/SGE.

5. Analyzes design sensitivities to variation, presents design opportunities to shrink memory area, power and improve performance, and provides integrated results verification.

“With increasing pressure for high yield and performance designs, designers are faced with a daunting level of analysis to understand the impact of variation on their designs,” said Amit Gupta, president and CEO of Solido Design. “Solido’s High-Sigma Monte Carlo meta-simulator has been successfully deployed at several companies, because alternate methods are too slow, insufficiently inaccurate, and do not scale across the range of circuits memory designers need to analyze.”

Please go here for more information on Solido’s High Sigma Monte Carlo for memory design

A high-sigma memory design white paper can be downloaded here: http://www.solidodesign.com/page/high-sigma-monte-carlo-for-high-yield-and-performance-memory-design/

About Solido Design Automation Inc.

Solido Design Automation Inc. is a leading provider of analysis and design software for high yield and performance IP and systems-on-a-chip (SOCs).  Solido plays an essential role in de-risking the variation impacts associated with the move to smaller processes, providing design teams maximum yield at the performance edge of memory, standard cell, low power and analog/RF design. Solido’s efficient software solutions address the exponential analysis at advanced process nodes without compromising time-to-market.  The privately held company is venture capital funded and has offices in the USA, Canada, Asia and Europe.  For further information, visit www.solidodesign.com or call 306-382-4100.

 

Contact:

Gloria Nichols
Launch Marketing
Email Contact
650-678-2219




Review Article Be the first to review this article
SolidCAM: Program your CNCs directly inside your existing CAD system.


Featured Video
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
Siemens Goes ECAD With Mentor Graphics Acquisition
Jobs
Mechanical Engineer for IDEX Corporation at West Jordan,, UT
GIS Analyst II for Air Worldwide at Boston, MA
Business Partner Manager for Cityworks - Azteca Systems, LLC at Sandy, UT
Senior Structural Engineer for Design Everest at San Francisco, CA
Upcoming Events
Design & Manufacturing, Feb 7 - 9, 2017 Anaheim Convention Center, Anaheim, CA at Anaheim Convention Center Anaheim CA - Feb 7 - 9, 2017
Innorobo 2017 at Docks de Paris Paris France - May 16 - 18, 2017
Display Week 2017 at Los Angeles Convention Center 1201 S Figueroa St Los Angeles CA - May 21 - 26, 2017



Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise