New 3D-Printed Plastic Heat Exchanger Shows Complex Geometries Are Possible from Additive Manufacturing

COLLEGE PARK, Md., Jan. 23, 2012 — (PRNewswire) — The A. James Clark School of Engineering at the University of Maryland, College Park and Stratasys, Inc., announce the successful design, fabrication, and test of a Webbed Tube Heat Exchanger (WTHX), believed to be the first plastic heat exchanger made by additive manufacturing. Fabricated at the Stratasys facility in Eden Prairie, Minn., the 3D-printed WTHX promises to expand the potential applications of polymer heat exchangers to small production volumes and cost-constrained systems.

The WTHX represents the first time that a plastic heat exchanger has been manufactured through Stratasys' Fused Deposition Modeling (FDM®) technology and used to successfully transfer heat through a polymer structure from a hot gas to a cold liquid. Room air, heated to 120 degrees Celsius was cooled by building water at 27 degrees Celsius, transferring nearly 65W of heat in the 500 cubic centimeter heat exchanger.

Juan Cevallos, a Ph.D. candidate and research assistant in the Thermal Management of Photonic and Electronic Systems (TherPES) Laboratory at the Clark School's Department of Mechanical Engineering, was responsible for testing the WTHX. Under the direction of Professor Avram Bar-Cohen–along with Professors S. K. Gupta, David Bigio, and Hugh Bruck–Cevallos has been working in collaboration with the Petroleum Institute in Abu Dhabi to advance polymer heat exchanger technology for seawater cooling of liquified natural gas processes, among other applications. The relatively high tool and assembly costs of low-volume polymer molding production led Bar-Cohen's research team to select an additive manufacturing technology that could build complex geometries in a single step. Stratasys' FDM technology provides that capability while using some of the strongest and most heat-resistant thermoplastics found among additive manufacturing technologies.

The WTHX geometry consists of a stack of rectangular flat plates, each containing an array of tubes that span the length of the plate and are separated by short webs. The tubular array carries the water, while the air flows in the gaps between the rectangular webbed-tube plates. The diameter of the tubes is selected to reduce the power required to pump the liquid while creating a "bumpy" surface on the gas-side that enhances heat transfer between the gas and liquid streams. Moreover, most of the heat transfer occurs directly across the thickness of the WTHX tubes, minimizing the deleterious effect of the low thermal conductivity of the polycarbonate resin.

About the A. James Clark School of Engineering
The Clark School of Engineering, situated on the rolling, 1,500-acre University of Maryland campus in College Park, Md., is one of the premier engineering schools in the U.S., with graduate and undergraduate education programs ranked in or near the Top 20. In 2011, the Clark School was ranked 11th in the world by the Institute of Higher Education and Center for World-Class Universities in its Academic Ranking of World Universities. Three faculty members affiliated with the Clark School were inducted into the National Academy of Engineering in 2010.

The school, which offers 13 graduate programs and 12 undergraduate programs, including degree and certification programs tailored for working professionals, is home to one of the most vibrant research programs in the country. The Clark School garnered research awards of $171 million last year. With emphasis in key areas such as energy, nanotechnology and materials, bioengineering, robotics, communications and networking, life cycle and reliability engineering, project management, intelligent transportation systems and aerospace, the Clark School is leading the way toward the next generations of engineering advances.

Visit the Clark School homepage at

SOURCE A. James Clark School of Engineering

A. James Clark School of Engineering
Stratasys, Inc.

Review Article Be the first to review this article
Autodesk - DelCAM

Featured Video
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
Apple Adding To Computer Product Line Minus Ports
Currently No Featured Jobs
Upcoming Events
Electric&Hybrid Aerospace Technology Symposium 2016 at Conference Centre East. Koelnmesse (East Entrance) Messeplatz 1 Cologne Germany - Nov 9 - 10, 2016
Autodesk University Las Vegas at Las Vegas NV - Nov 15 - 17, 2016
Design & Manufacturing, Feb 7 - 9, 2017 Anaheim Convention Center, Anaheim, CA at Anaheim Convention Center Anaheim CA - Feb 7 - 9, 2017
TurboCAD pro : Limited Time offer

Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise