Mentor Graphics Announces Completion of 20 nm Test Chip Tapeout with STMicroelectronics Using Olympus-SoC Place and Route System

WILSONVILLE, Ore. — (BUSINESS WIRE) — November 4, 2011Mentor Graphics Corporation (NASDAQ: MENT) today announced the successful tapeout of a 20 nm test chip in collaboration with STMicroelectronics, marking a significant milestone in the development of a complete Mentor® design-to-silicon solution for next-generation process technology. The test chip was implemented using the Olympus-SoC™ place and route system, and verified using the Calibre® nmDRC platform, which is the verification and double patterning solution used by R&D teams at STMicroelectronics. Together, the Olympus-SoC, Calibre and Tessent® silicon test and yield analysis products provide a comprehensive flow for 20 nm IC development.

“The Olympus-SoC place and route system has been proven on many tapeouts across multiple nodes and different application areas,” said Pravin Madhani, general manager of the Mentor Place and Route Group. “The 20 nm node has a unique set of new requirements including double patterning. Working with STMicroelectronics as a teaching customer and strategic investment partner in the DeCADE program has enabled us to make rapid progress in delivering advanced implementation solutions for 20 nm enablement.”

The Olympus-SoC place and route system is a complete netlist-to-GDSII system and is built on patented concurrent multi-corner multi-mode (MCMM) optimization, high capacity data model, advanced low power capabilities and integration with the Calibre® platform for faster manufacturing closure. The OpenRouter architecture of the Olympus-SoC product enables native invocation of Calibre engines during design and uses the foundry signoff decks to ensure that the resulting layout is decomposable for multi-patterning, in addition to being DRC/LVS/DFM signoff clean.

“Increased process complexity and variability, lithography limitations, large design sizes and extreme low power add to the IC design challenges at 20 nm,” said Philippe Magarshack, group vice president at STMicroelectronics Technology Research and Development. “Through the ISDA and the DeCADE joint development program, we are working very closely with Mentor Graphics on various aspects of 20 nm design enablement. We are pleased with the Olympus-SoC integrated platform’s ability to deliver a 20 nm place and route solution with high quality of results, which we recently demonstrated on a 20 nm test chip tapeout. We consider this to be a significant milestone toward demonstrating our 20 nm readiness.”

About DeCADE

The joint-development project named DeCADE builds on advanced design solutions for SoC (System-On-Chip) development. DeCADE reinforces the Crolles cooperative R&D cluster, which gathers partners that develop and enable low-power SoCs and value-added application-specific technologies, and is a great example of a project developed within the framework of the Nano2012 program. Nano2012 is a strategic R&D program, led by STMicroelectronics, which gathers research institutes and industrial partners and is supported by French national, regional and local authorities.

About Mentor Graphics

Mentor Graphics Corporation (NASDAQ: MENT) is a world leader in electronic hardware and software design solutions, providing products, consulting services and award-winning support for the world’s most successful electronic, semiconductor and systems companies. Established in 1981, the company reported revenues over the last 12 months of about $915 million. Corporate headquarters are located at 8005 S.W. Boeckman Road, Wilsonville, Oregon 97070-7777. World Wide Web site: http://www.mentor.com/.

(Mentor Graphics, Mentor, Calibre and Tessent are registered trademarks, and Olympus-SoC is a trademark of Mentor Graphics Corporation. All other company or product names are the registered trademarks or trademarks of their respective owners.)



Contact:

Mentor Graphics
Gene Forte, 503-685-1193
Email Contact
or
Sonia Harrison, 503-685-1165
Email Contact




Review Article Be the first to review this article

SolidCAM: Cutting Webinar

Featured Video
Editorial
Jeff RoweJeff's MCAD Blogging
by Jeff Rowe
PTC Marches On With New Vuforia AR Platform Release
Jobs
GIS Software Developer for UDC at Englewood, CO
Vice President, Transportation Services for Associated General Contractors of New York State at Albany, NY
GIS Analyst for G2 Partners LLC at San Ramon, CA
Architectural Designer for Champion Home Builders at Troy, MI
Upcoming Events
ASSESS 2017 CONGRESS at Bolger Center Potomac MD - Nov 1 - 3, 2017
FABTECH 2017 at McCormick Place Chicago IL - Nov 6 - 9, 2017
ATX MINNEAPOLIS 2017 at Minneapolis MN - Nov 8 - 9, 2017
2017 China Chongqing International Machine Tool Show (CCIMT) at Chongqing International Expo Center, Yubei Chongqing China - Nov 13 - 16, 2017



Internet Business Systems © 2017 Internet Business Systems, Inc.
25 North 14th Steet, Suite 710, San Jose, CA 95112
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise