Power, accuracy and noise aspects in CMOS mixed-signal design

Title: Power, accuracy and noise aspects in CMOS mixed-signal design
Author: Sanduleanu, Mihai Adrian Tiberiu
ISBN: 90-3651265-4
©1999, Mihai A.T. Sanduleanu

Table of Contents

Selected Symbols and Abbreviations
 
Chapter 1   Introduction
  1.1. Motivation
  1.2. Problem definition
  1.3. Scope and outline
  References
 
Chapter 2 Power considerations in sub-micron digital CMOS
  2.1. Introduction
  2.2. Fundamental limits
  2.3. From fundamental limits to practical limits of power. An architecture level approach
  2.4. S/N ratio and power in fixed point applications
  2.5. Adders and computational power
  2.6. Ways to low-power in digital
  2.7. Example of a digital video filter
  2.8. Conclusions
  2.8. References
 
Chapter 3 Power considerations in sub-micron analog CMOS
  3.1. Introduction
  3.2. Process tuning towards digital needs. Consequences on analog
  3.3. Fundamental limits
  3.4. From fundamental limits to practical limits of power. Noise related power
  3.5. From fundamental limits to practical limits of power. Mismatch related power
  3.6. Power estimations in continuous time filters
  3.7. Conclusions
  References
 
Chapter 4 Gm-C integrators for low-power and low voltage applications. A gaussian polyphase filter for mobile transceivers in 0.35mm CMOS
  4.1. Introduction
  4.2. Large swing and high linearity transconductor
  4.3. Low voltage current Gm-C integrator with high power efficiency
  4.4. Low-power luminance video filter. Noise driven power
  4.5. Low-power, gaussian, polyphase filter for mobile transceivers. Matching driven power
  4.6. Conclusions
  References
 
Chapter 5 Chopping: a technique for noise and offset reduction
  5.1. Introduction
  5.2. Ways to reduce offset and 1/f noise
  5.3. Chopping seen as a modulation technique
  5.4. Noise modulation
  5.5. Chopped amplifiers and offset reduction
  5.6. Low-power low-voltage chopped transconductance amplifier for noise and offset reduction
  5.7. A low-power bandgap voltage reference
  5.8. Conclusions
  References
 
Chapter 6 Low-noise, low residual offset, chopped amplifiers for high-end application
  6.1. Introduction
  6.2. Low-pass filtering in a digital audio system. Application specific constraints
  6.3. The gain stage
  6.4. A low noise, low residual offset, chopped amplifier in 0.8mm CMOS
  6.5. A low noise, low residual offset, chopped amplifier in 0.5mm CMOS
  6.6. Conclusions
  References
 
Chapter 7 A 16-bit D/A interface with Sinc approximated semidigital reconstruction filter
  7.1. Introduction
  7.2. Bitstream D/A conversion system with time-discrete filtering
  7.3. S-D modulators and noise shaping
  7.4. Semidigital FIR filter principles
  7.5. Semidigital FIR filter design
  7.6. Noise properties of the D/A interface
  7.7. Realisation
  7.8. Experimental results
  7.9. Interpolative D/A converter with Sinc approximation in the time domain
  7.10. Conclusions
  References
 
Chapter 8 Conclusions
  8.1. Summary
  8.2. Conclusions
  8.3. Original contributions
  8.4. Recommendations for further research
 
Appendix 1
 
Appendix 2
 
Appendix 3
 
HP

SolidCAM: Program your CNCs directly inside your existing CAD system.

Featured Video
Jobs
Principal Research Mechatronics Engineer for Verb Surgical at Mountain View, CA
Senior Mechanical Engineer for Verb Surgical at Mountain View, CA
CAD Systems Administrator for KLA-Tencor at Milpitas, CA
Industrial Designer Intern – Spring 2017 for Nvidia at Santa Clara, CA
Lead Geospatial Analyst for Alion at McLean, VA
Upcoming Events
PI APPAREL Hong Kong 2017 at SHANGRI-LA KOWLOON 64 Mody Road Tsim Sha Tsui East Kowloon Hong Kong - Apr 5 - 6, 2017
SOLIDWORKS intro and hands on session – Slough at Baylis House, Slough, Berkshire, SL1 3PB Slough United Kingdom - Apr 7, 2017
PMTS 2017 at Greater Columbus Convention Center Exhibit Halls E, F, & D 400 North High St. Columbus OH - Apr 25 - 27, 2017
Engineer 3D! Training + Technology Conference at Hyatt Regency Milwaukee 333 West Kilbourn Avenue Milwaukee WI - Apr 25 - 26, 2017
MasterCAM



Internet Business Systems © 2017 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise