Logic Design for Array-Based Circuits

by Donnamaie E. White

Copyright © 1996, 2001, 2002 Donnamaie E. White

 

Introduction

Last Edit July 22, 2001


Update 2000

When I first wrote this book, I had spent a considerable amount of time in the Bit-Slice and ASIC industry. The book reflected the design procedures at that moment. It was a reflection of the class I taught at AMCC and at UCSD for 11.5 years. From there I developed and taught the technical training classes for CBA (cell-based array) designs. Now, even CBA is beginning to fade as standard cells take over a the dominant array-based technology.

As of January 2001, there have been some changes, although not as many as people would like to think. The basic design flow? - It is still with us.

  • The size of the designs has changed from what could be handled by a human (up to 50,000 gates) to what must be handled by a computer (12 million gates). We are seeing designs that run 4-6 millions gates per ASIC and will be seeing 10-12 million designs shortly.
  • Wafers have gone from 3" to 6-8" and are headed for 12".
  • From primarily bipolar, I now work almost exclusively with CMOS.
  • The process technology has gone from 5 microns to 0.18 deep sub-micron, and everything bipolar designers worried about is now the headache that concerns CMOS designers - namely, that gate delays are practically negligible compared to interconnect delays. DSM (deep sub-micron) refers to this phomonina.
  • By 1998, CBA ASICs still ruled, but by 2000 standard cells had become dominant, producing smaller and faster designs.
  • Libraries still exist but now macro selection is by a synthesis software package and 85% of designs are done with the Synopsys Design Compiler package. Cadence now has a competitive synthesis package.
  • Schematic capture is pretty much an anachronism and design are specified in Verilog or VHDL (RTL).
  • Software tools take the design from RTL (register-transfer logic) through wafer-verification, with software like Dracula, Vampire), performing ATT (antenna checking), ERCs (electrical rules checking), DRCs (design rule checking). Manual operations are no longer feasible.
  • RAM and ROM onboard an ASIC is no longer unusual.
  • IP (intellectual property) blocks are in common use. Design-Reuse is a buzzword. IP may be multi-layered and fixed (hard IP), or soft IP where a netlist is incorporated and the block may be altered by synthesis steps.
  • Vectors are generated by automatic test vector generation software.
  • Designs are made DFT (design for test) as a routine step in the compile process. DFT is no longer an option.
  • Software can tell you if your design is testable and if it is routable.
  • Place and Route are no longer a last step in the process. Floorplanners are required for any sizable design. Cadence's Gate Ensemble and Silicon Ensemble were the leaders in Place and Route. Synopsys has the Chip Architect floorplanner. Cadence has the Logical and Physical design planners. Avant! has Planit! for floorplanning tasks.
  • Everybody's floorplanner has to talk to everybody's synthesis tool and they both have to talk to everybody's place&route software. Everybody has to talk to PrimeTime.
  • What AMCC called "intermediate annotation" is what is produced during floorplanning and it's use is not optional..
  • EDIF became the standard for netlists. There is no more concern about whose netlist went where. EDIF is used to input to floorplanners, and EDIF is produced by the systhesis tools and by the place&route tool.
  • DB has become a standard format.
  • DEF (design exchange format - Cadence) became the standard for input to place&route
  • PDEF 2.0 is the standard output of the floorplanners and is now standard input to place&route software. PDEF 3.0 is on the horizon.
  • SDF 2.0 is used for delay files and can be created by PrimeTime from delay information from most floorplanners and place&route tools.
  • SPICE files are still with us
  • VCS, VSS and related tools perform simulation.
  • GDSII is for building the basedie layers and GDSII is produced by the place&route software
  • PrimeTime is the standard for static timing analysis (85% of design are verified with that software).
  • Designers no longer have to "fit" their designs into a fixed-size chip with a fixed I/O count (cells in the I/O ring). Dies are designed to fit the design. Holes are punched through the layers to accommodate IP blocks (Hard IP blocks) and software exists to "stitch" the IP blocks into the basedie.
  • You may not "diddle" with parametric specifications. If you have a different set of operating conditions, you must go back to the library vendor for new library specifications. The slightest variation can have dire consequences in the results.
  • The axiom that the engineer who knew the library could do better designs than a more experienced engineer who did not, still holds. You may "direct" the use of macros by the synthesis tools.
  • Tcl has become the standard interface scripting language.

In fact, Synopsys alone has approximately 42 different software tools available to help create an ASIC design. Design flow from RTL to wafer fab is the focus of most vendors today.

 

 

 

 

 

 

 

 

 

 

 

 

 

Copyright @ 2001, 2002 Donnamaie E. White, White Enterprises
For problems or questions on these pages, contact dew@Donnamaie.com




Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise