We included a delay of one Verilog time unit in line 15 of the testbench model (allowing time to progress), but we did not specify the units—they could be nanoseconds or days. Thus, behavioral simulation can only tell us if our design does not work; it cannot tell us that real hardware will work.
We use logic synthesis to produce a structural model from a behavioral model. The following comparator/MUX model is adapted from the example in Section 12.11 , “ Performance-Driven Synthesis ” (optimized for a 0.6 m m standard-cell library):
Logic simulation requires Verilog models for the following six logic cells: mx21d1 (2:1 MUX), oa03d1 (OAI221), nd02d0 (two-input NAND), oa04d1 (OAI21), in01d0 (inverter), and an02d1 (two-input AND). These models are part of an ASIC library (often encoded so that they cannot be seen) and thus, from this point on, the designer is dependent on a particular ASIC library company. As an example of this dependence, notice that some of the names in the preceding code have changed from uppercase (in Figure 12.8 on p. 624) to lowercase. Verilog is case sensitive and we are using a cell library that uses lowercase. Most unfortunately, there are no standards for names, cell functions, or the use of case in ASIC libraries.
To simulate the optimized structural model, module comp_mux_o2.v , we use the library cell models (module mx21d1 and the other five that are not shown here) together with the following new testbench model:
In this testbench we have instantiated two models: a reference model (module reference ) and a derived model (module comp_mux_o , the optimized structural model). The high-level behavioral model that represents the initial system specification (module reference ) may be different from the model that we use as input to the logic-synthesis tool (module comp_mux ). Which is the real reference model? We postpone this question until we discuss formal verification in Section 13.8 . For the moment, we shall simply perform simulations to check the reference model against the derived model. The simulation results are as follows:
(A summary is printed at the end of the simulation to catch any errors.) The next step is to examine the timing of the structural model (by switching the leading '//' from line 6 to 16 in module comp_mux_testbench2 ). It is important to simulate using the worst-case delays by using a command-line switch as follows: verilog +maxdelays . We can then find the longest path delay by searching through the simulator output, part of which follows:
At time 280 ns, the input vectors, x and y , switch from ( x = 3 , y = 3 ) to ( x = 3 , y = 4 ). The output of the derived model (which should be equal to the smaller of x and y ) is the same for both of these input vectors and should remain unchanged. In fact there is a glitch at the output of the derived model, as it changes from 3 to 0 and back to 3 again, taking 3.17 ns to settle to its final value (this is the longest delay that occurs using this testbench). The glitch occurs because one of the input vectors (input y ) changes from '011' (3 in decimal) to '100' (decimal 4). Changing several input bits simultaneously causes the output to vacillate.
Notice that the nominal and worst-case simulations will not necessarily give the same longest path delay. In addition the longest path delay found using this testbench is not necessarily the critical path delay. For example, the longest, and therefore critical, path delay might result from a transition from x = 3 , y = 4 to x = 4 , y = 3 (to choose a random but possible candidate set of input vectors). This testbench does not include tests with such transitions. To find the critical path using logic simulation requires simulating all possible input transitions (64 ¥ 64 = 4096) and then sifting through the output to find the critical path.
Vector-based simulation (or dynamic simulation ) can show us that our design functions correctly—hence the name functional simulation. However, functional simulation does not work well if we wish to find the critical path. For this we turn to a different type of simulation—static simulation or static timing analysis.
A timing analyzer answers the question: “What is the longest delay in my circuit?” Table 13.1 shows the timing analysis of the comparator/MUX structural model, module comp_mux_o2.v . The longest or critical path delay is 4.06 ns under the following worst-case operating conditions: worst-case process, V DD = 4.75 V, and T = 70 ∞ C (the same conditions as used for the library data book delay values). The timing analyzer gives us only the critical path and its delay. A timing analyzer does not give us the input vectors that will activate the critical path. In fact input vectors may not exist to activate the critical path. For example, it may be that the decimal values of the input vectors to the comparator/MUX may never differ by more than four, but the timing-analysis tool cannot use this information. Future timing-analysis tools may consider such factors, called Boolean relations , but at present they do not.
Section 13.2.1 explained why dynamic functional simulation does not necessarily find the critical path delay. Nevertheless, the difference between the longest path delay found using functional simulation, 3.17 ns, and the critical path delay reported by the static timing-analysis tool, 4.06 ns, is surprising. This difference occurs because the timing analysis accounts for the loading of each logic cell by the input capacitance of the logic cells that follow, but the simplified Verilog models used for functional simulation in Section 13.2.1 did not include the effects of capacitive loading. For example, in the model for the logic cell mx21d1 , the (rising) delay from the i0 input to the output z , was fixed at 0.900 ns worst case (the maximum delay value is the third number in the first triplet in line 7 of module mx21d1 ). Normally library models include another portion that adjusts the timing of each logic cell—this portion was removed to simplify the model mx21d1 shown in Section 13.2.1 .
Most timing analyzers do not consider the function of the logic when they search for the critical path. Thus, for example, the following code models z = NAND(a, NOT(a)) , which means that the output, z , is always '1' .
Paths such as this, which are impossible to activate, are known as false paths . Timing analysis is essential to ASIC design but has limitations. A timing-analysis tool is more logic calculator than logic simulator.
To illustrate the differences between functional simulation, timing analysis, and gate-level simulation, we shall simulate the comparator/MUX critical path (the path is shown in Table 13.1 ). We start by trying to find vectors that activate this critical path by working forward from the beginning of the critical path, the input a , toward the end of the critical path, output outp , as follows:
We have now contradicted ourselves. In step 1 we saw that the initial value of a must be a '0' . The critical path is thus a false path. Nevertheless we shall proceed. We set the initial input vector to ( a = '110' , b = '111') and then to ( a = '111' , b = '110' ). These vectors allow the change on a to propagate to the select signal of the MUX, mx21d1 , cell instance b1_i5 . In decimal we are changing a from 6 to 7, and b from 7 to 6; the output should remain unchanged at 6. The simulation results from the gate-level simulator we shall use ( CompassSim) can be displayed graphically or in the text form that follows:
The code 'Buuu denotes that the output is initially, at t = 0 ns, a binary vector of three unknown or unsettled signals. The output bits become valid as follows: outp at 0.47 ns, outp at 0.97 ns, and outp at 4.08 ns. The output is stable at 'D6 (decimal 6) or '110' at t = 10 ns when the input vectors are changed in an attempt to activate the critical path. The output glitches from 'D6 ( '110' ) to 'D7 ( '111' ) at t = 10.97 ns and back to 'D6 again at t = 14.15 ns. Thus, the output bit, outp , takes a total of 4.15 ns to settle.
Can we explain this behavior? The data book entry for the mx21d1 logic cell gives the following equation for the rising delay as a function of Cld (the load capacitance, excluding the output capacitance of the logic cell itself, expressed in picofarads):
The capacitance, Cld , at the output of each MUX is zero (because nothing is connected to the outputs). From Eq. 13.1 , the path delay from the input, a , to the output, outp , is thus 0.97 ns. This explains why the output, outp , changes from '0' to '1' at t = 10.97 ns, 0.97 ns after a change occurs on a .
The gate-level simulation predicts that the input, a , to the MUX will change before the changes on the inputs have time to propagate to the MUX select. Finally, at t = 14.15 ns, the MUX select will change and switch the output, outp , back to '0' again. The total delay for this input vector stimulus is thus 4.15 ns. Even though this path is a false path (as far as timing analysis is concerned), it is a critical path. It is indeed necessary to wait for 4.15 ns before using the output signal of this circuit. A timing analyzer can only offer us a guarantee that there is no other path that is slower than the critical path.
The timing analyzer predicted a critical path delay of 4.06 ns compared to the gate-level simulation prediction of 4.15 ns. We can check our results by using another gate-level simulator ( QSim) which uses a slightly different algorithm. Here is the output (with the same input vectors as before):
The simulator is adding capacitance to the outputs of each of the logic cells to model the parasitic net capacitance ( interconnect capacitance or wire capacitance) that will be present in the physical layout. The simulator adds 0.01 pF ( defCapacitance ) on each node and another 0.01 pF ( incCapacitance ) for each pin (logic cell input) attached to a node. The model that predicts these values is known as a wire-load model , wire-delay model , or interconnect model . Changing the wire-load model parameters to zero and repeating the simulation changes the critical-path delay to 4.06 ns, which agrees exactly with the logic-synthesizer timing analysis. This emphasizes that the net capacitance may contribute a significant delay.
Armed with this information, let us return to the timing analysis report of Table 13.1 (the part of this table we shall focus on follows) and examine how a timing analyzer handles net capacitance.
The total capacitance at the output node of logic cell instance b1_i3 is 0.08 pF. This figure is the sum of the logic cell ( nd02d0 ) output capacitance of cell instance b1_i3 (equal to 0.038 pF) and Cld , the input capacitance of the next cell, b1_i2 (also an nd02d0 ), equal to 0.042 pF.
Having explained the capacitance figures in the timing-analysis report, let us turn to the delay figures. The fall-time delay equation for a nd02d0 logic cell (again from the vsc450 library data book) is as follows:
Notice 0.11 ns = 2.89 nspF–1 ¥ 0.038 pF, and this figure in Eq. 13.3 is the part of the cell delay attributed to the cell output capacitance. The ramp delay in the timing analysis (under the heading rampDel in Table 13.1 ) is the sum of the last two terms in Eq. 13.3 . Thus, the ramp delay is 0.11 + (2.89 ¥ 0.042 ) = 0.231 ns (since Cld is 0.042 pF). The total delay (under incr in Table 13.1 ) is 0.08 + 0.231 = 0.31 ns.
Normally we do not check our simulation results this thoroughly. However, we can only trust the tools if we understand what they are doing, how they work, their limitations, and we are able to check that the results are reasonable.
1. 1Using a 0.8 m m standard-cell library, VLSI Technology vsc450. Worst-case environment: worst-case process, V DD = 4.75 V, and T = 70 °C. No wire capacitance, no input or output capacitance, prop–ramp timing model. The structural model was synthesized and optimized using a 0.6 m m library, but this timing analysis was performed using the 0.8 m m library. This is because the library models are simpler for the 0.8 m m library and thus easier to explain in the text.
© 2018 Internet Business Systems, Inc.
25 North 14th Steet, Suite 710, San Jose, CA 95112
+1 (408) 882-6554 — Contact Us, or visit our other sites: