E> 9.1 Schematic Entry

9.1  Schematic Entry

Schematic entry is the most common method of design entry for ASICs and is likely to be useful in one form or another for some time. HDLs are replacing conventional gate-level schematic entry, but new graphical tools based on schematic entry are now being used to create large amounts of HDL code.

Circuit schematics are drawn on schematic sheets . Standard schematic sheet sizes ( Table 9.1 ) are ANSI A–E (more common in the United States) and ISO A4–A0 (more common in Europe). Usually a frame or border is drawn around the schematic containing boxes that list the name and number of the schematic page, the designer, the date of the drawing, and a list of any modifications or changes.

TABLE 9.1  ANSI (American National Standards Institute) and ISO (International Standards Organization) schematic sheet sizes.

ANSI sheet

Size (inches)

ISO sheet

Size (cm)


8.5 ¥ 11


21.0 ¥ 14.8


11 ¥ 17


29.7 ¥ 21.0


17 ¥ 22


42.0 ¥ 29.7


22 ¥ 34


59.4 ¥ 42.0


34 ¥ 44


84.0 ¥ 59.4




118.9 ¥ 84.0

Figure 9.1 shows the “ spades” and “ shovels,” the recognized symbols for AND, NAND, OR, and NOR gates. One of the problems with these recommendations is that the corner points of the shapes do not always lie on a grid point (using a reasonable grid size).


FIGURE 9.1  IEEE-recommended dimensions and their construction for logic-gate symbols. (a) NAND gate (b) exclusive-OR gate (an OR gate is a subset).

Figure 9.2 shows some pictorial definitions of objects you can use in a simple schematic. We shall discuss the different types of objects that might appear in an ASIC schematic first and then discuss the different types of connections.


FIGURE 9.2  Terms used in circuit schematics.

Schematic-entry tools for ASIC design are similar to those for printed-circuit board (PCB) design. The basic object on a PCB schematic is a component or device —a TTL IC or resistor, for example. There may be several hundred components on a typical PCB. If we think of a logic gate on an ASIC as being equivalent to a component on a PCB, then a large ASIC contains hundreds of thousands of components. We can normally draw every component on a few schematic sheets for a PCB, but drawing every component on an ASIC schematic is impractical.

9.1.1  Hierarchical Design

Hierarchy reduces the size and complexity of a schematic. Suppose a building has 10 floors and contains several hundred offices but only three different basic office plans. Furthermore, suppose each of the floors above the ground floor that contains the lobby is identical. Then the plans for the whole building need only show detailed plans for the ground floor and one of the upper floors. The plans for the upper floor need only show the locations of each office and the office type. We can then use a separate set of three detailed plans for each of the different office types. All these different plans together form a nested structure that is a hierarchical design . The plan for the whole building is the top-level plan. The plans for the individual offices are the lowest level. To clarify the relationship between different levels of hierarchy we say that a subschematic (an office) is a child of the parent schematic (the floor containing offices). An electrical schematic can contain subschematics. The subschematic, in turn, may contain other subschematics. Figure 9.3 illustrates the principles of schematic hierarchical design.


FIGURE 9.3  Schematic example showing hierarchical design. (a) The schematic of a half-adder, the subschematic of cell HADD. (b) A schematic symbol for the half adder. (c) A schematic that uses the half-adder cell. (d) The hierarchy of cell HADD.

The alternative to hierarchical design is to draw all of the ASIC components on one giant schematic, with no hierarchy, in a flat design . For a modern ASIC containing thousands or more logic gates using a flat design or a flat schematic would be hopelessly impractical. Sometimes we do use flat netlists though.

9.1.2 The Cell Library

Components in an ASIC schematic are chosen from a library of cells. Library elements for all types of ASICs are sometimes also known as modules . Unfortunately the term module will have a very specific meaning when we come to discuss hardware description languages. To avoid any chance of confusion I use the term cell to mean either a cell, a module, a macro, or a book from an ASIC library. Library cells are equivalent to the offices in our office building.

Most ASIC companies provide a schematic library of primitive gates to be used for schematic entry. The first problem with ASIC schematic libraries is that there are no naming conventions. For example, a primitive two-input NAND gate in a Xilinx FPGA library does not have the same name as the two-input NAND gate in an LSI Logic gate-array library. This means that you cannot take a schematic that you used to create a prototype product using a Xilinx FPGA and use that schematic to create an LSI Logic gate array for production (something you might very likely want to do). As soon as you start entering a schematic using a library from an ASIC vendor, you are, to some extent, making a commitment to use that vendor’s ASIC. Most ASIC designers are much happier maintaining a large degree of vendor independence.

A second problem with ASIC schematic libraries is that there are no standards for cell behavior. For example, a two-input MUX in an Actel library operates so that the input labeled A is selected when the MUX select input S = '0'. A two-input MUX in a VLSI Technology library operates in the reverse fashion, so that the input labeled B is selected when S = '0'. These types of differences can cause hard-to-find problems when trying to convert a schematic from one vendor to another by hand. These problems make changing or retargeting schematics from one vendor to another difficult. This process is sometimes known as porting a design.

Library cells that represent basic logic gates, such as a NAND gate, are known as primitive cells , usually referred to just as cells. In a hierarchical ASIC design a cell may be a NAND gate, a flip-flop, a multiplier, or even a microprocessor, for example. To use the office building analogy again, each of the three basic office types is a primitive cell. However, the plan for the second floor is also a cell. The second-floor cell is a subschematic of the schematic for the whole building. Now we see why the commonly accepted use of the term cell in schematic entry can be so confusing. The term cell is used to represent both primitive cells and subschematics. These are two different, but closely related, things.

There are two types of macros for MGAs and programmable ASICs. The most common type of macro is a hard macro that includes placement information. A hard macro can change in position and orientation, but the relative location of the transistors, other layout, and wiring inside the macro is fixed. A soft macro contains only connection information (between transistors for a gate array or between logic cells for a programmable ASIC). Thus the placement and wiring for a soft macro can vary. This means that the timing parameters for a soft macro can only be determined after you complete the place-and-route step. For this reason the basic library elements for MGAs and programmable ASICs, such as NAND gates, flip-flops, and so on, are hard macros.

A standard cell contains layout information on all mask levels. An MGA hard macro contains layout information on just the metal, contact, and via layers. An MGA soft macro or programmable ASIC macro does not contain any layout information at all, just the details of connections to be made inside the macro.

We can stretch the office building analogy to explain the difference between hard and soft macros. A hard macro would be an office with fixed walls in which you are not allowed to move the furniture. A soft macro would be an office with partitions in which you can move the furniture around and you can also change the shape of your office by moving the partitions.

9.1.3 Names

Each of the cells, primitive or not, that you place on an ASIC schematic has a cell name . Each use of a cell is a different instance of that cell, and we give each instance a unique instance name . A cell instance is somewhere between a copy and a reference to a cell in a library. An analogy would be the pictures of hamburgers on the wall in a fast-food restaurant. The pictures are somewhere between a copy and a reference to a real hamburger.

We represent each cell instance by a picture or icon , also known as a symbol . We can represent primitive cells, such as NAND and NOR gates, with familiar icons that look like spades and shovels. Some schematic editors offer the option of switching between these familiar icons and using the rectangular IEEE standard symbols for logic gates. Unfortunately the term icon is also often used to refer to any of the pictures on a schematic, including those that represent subschematics. There is no accepted way to differentiate between an icon that represents a primitive cell and one that represents a subschematic that may be in turn a collection of primitive cells. In fact, there is usually no easy way to tell by looking at a schematic which icons represent primitive cells and which represent subschematics.

We will have three different icons for each of the three different primitive offices in the imaginary office building example of Section 9.1.1 . We also will have icons to represent the ground floor and the plan for the other floors. We shall call the common plan for the second through tenth floors, Floor . Then we say that the second floor is an instance of the cell name Floor . The third through tenth floors are also instances of the cell name Floor . The same icon will be used to represent the second through tenth floors, but each will have a unique instance name. We shall give them instance names: FloorTwo , FloorThree , ... , FloorTen . We say that FloorTwo through FloorTen are unique instance names of the cell name Floor .

At the risk of further confusion I should point out that, strictly speaking, the definition of a primitive cell depends on the type of library being used. Schematic-entry libraries for the ASIC designer stop at the level of NAND gates and other similar low-level logic gates. Then, as far as the ASIC designer is concerned, the primitive cells are these logic gates. However, from the view of the library designer there is another level of hierarchy below the level of logic gates. The library designer needs to work with libraries that contain schematics of the gates themselves, and so at this level the primitive cells are transistors.

Let us look at the building analogy again to understand the subtleties of primitive cells. A building contractor need only concern himself with the plans for our office building down to the level of the offices. To the building contractor the primitive cells are the offices. Suppose that the first of the three different office types is a corner office, the second office type has a window, and a third office type is without a window. We shall call these office cells: CornerOffice , WindowOffice , and NoWindowOffice . These cells are primitive cells as far as the contractor is concerned. However, when discussing the plans with a client, the architect of our building will also need to see how each offices is furnished. The architect needs to see a level of detail of each office that is more complicated than needed by the building contractor. The architect needs to see the cells that represent the tables, chairs, and desks that make up each type of office. To the architect the primitive cells are a library containing cells such as chair , table , and desk .

9.1.4 Schematic Icons and Symbols

Most schematic-entry programs allow the designer to draw special or custom icons. In addition, the schematic-entry tool will also usually create an icon automatically for a subschematic that is used in a higher-level schematic. This is a derived icon , or derived symbol . The external connections of the subschematic are automatically attached to the icon, usually a rectangle.

Figure 9.4 (c) shows what a derived icon for a cell, DLAT , might look like (we could also have drawn this by hand). The subschematic for DLAT is shown in Figure 9.4 (b). We say that the inverter with the instance name inv1 in the subschematic is a subcell (or submodule) of the cell DLAT . Alternatively we say that cell instance inv1 is a child of the cell DLAT , and cell DLAT is a parent of cell instance inv1 .


FIGURE 9.4  A cell and its subschematic. (a) A schematic library containing icons for the primitive cells. (b) A subschematic for a cell, DLAT, showing the instance names for the primitive cells. (c) A symbol for cell DLAT.

Figure 9.5 (a) shows a more complex subschematic for a 4-bit latch. Each primitive cell instance in this schematic must have a unique name. This can get very tiresome for large circuits. Instead of creating complex, but repetitive, subschematics for complex cells we can use hierarchy.


FIGURE 9.5  A 4-bit latch: (a) drawn as a flat schematic from gate-level primitives, (b) drawn as four instances of the cell symbol DLAT, (c) drawn using a vectored instance of the DLAT cell symbol with cardinality of 4, (d) drawn using a new cell symbol with cell name FourBit.

Figure 9.5 (b) shows a hierarchical subschematic for a cell FourBit , which in turn uses four instances of the cell DLAT . The four instances of DLAT in Figure 9.5 (b) have different instance names: L1 , L2 , L3 , and L4 . Notice that we cannot use just one name for the four instances of DLAT to indicate that they are all the same cell. If we did, we could not differentiate between L1 and L2 , for example.

The vertical row of instances in Figure 9.5 (b) looks like a vector of elements. Figure 9.5 (c) shows a vectored instance representing four copies of the DLAT cell. We say the cardinality of this instance is 4. Tools normally use bold lines or some other distinguishing feature to represent a vectored instance. The cardinality information is often shown as a vector. Thus L[1:4] represents four instances: L[1] , L[2] , L[3] , L[4] . This is convenient because now we can see that all subcells are identical copies of L , but we have a unique name for each.

Finally, as shown in Figure 9.5 (d) we can create a new symbol for the 4-bit latch, FourBit . The symbol for FourBit has a 4-bit-wide input bus for the four D inputs, and a 4-bit wide output bus for the four Q outputs. The subschematic for FourBit could be either Figure 9.5 (a), (b), or (c) (though the exact naming of the inputs and outputs and their attachment to the buses may be different in each case).

We need a convention to distinguish, for example, between the inverter subcells, inv1 , which are children of the cell DLAT , which are in turn children of the cell FourBit . Most schematic-entry tools do this by combining the instance names of the subcells in a hierarchical manner using a special character as a delimiter. For example, if we drew the subschematic as in Figure 9.5 (b), the four inverters in FourBit might be named L1.inv1 , L2.inv1 , L3.inv1 , and L4.inv1 . Once again this makes it clear that the inverters, inv1 , are identical in all four subcells.

In our office building example, the offices are subcells of the cell Floor . Suppose you and I both have corner offices. Mine is on the second floor and yours is above mine on the third floor. My office is 211 and your office is 311. Another way to name our offices on a building plan might be FloorTwo.11 for my office and FloorThree.11 for your office. This shows that FloorTwo.11 is a subcell of FloorTwo and also makes it clear that, apart from being on different floors, your office and mine are identical. Both our offices have instance names 11 and are instances of cell name Corner .

9.1.5 Nets

The schematics shown in Figure 9.4 contain both local nets and external nets . An example of a local net in Figure 9.4 (b) is n1 , the connection between the output terminal of the AND cell and1 to the OR cell or1 . When the four copies of this circuit are placed in the parent cell FourBit in Figure 9.5 (d), four copies of net n1 are created. Since the four nets named n1 are not actually electrically connected, even though they have the same name at the lowest hierarchical level, we must somehow find a way to uniquely identify each net.

The usual convention for naming nets in a hierarchical schematic uses the parent cell instance name as a prefix to the local net name. A special character ( ':' '/' '$' '#' for example) that is not allowed to appear in names is used as a delimiter to separate the net name from the cell instance name. Supposing that we drew the subschematic for cell FourBit as shown in Figure 9.5 (b), the four different nets labeled n1 might then become:

FourBit .L1:n1 FourBit .L2:n1 FourBit .L3:n1 FourBit .L4:n1

This naming is usually done automatically by the schematic-entry tool.

The schematic DLAT also contains three external nets: D, EN, and Q . The terminals on the symbol DLAT connect these nets to other nets in the hierarchical level above. For example, the signal Trigger:flag in Figure 9.4 (c) is also Trigger.DLAT:Q . Each schematic tool handles this situation differently, and life becomes especially difficult when we need to refer to these nodes from a simulator outside the schematic tool, for example. HDLs such as VHDL and Verilog have a very precise and well-defined standard for naming nets in hierarchical structures.

9.1.6 Schematic Entry for ASICs and PCBs

A symbol on a schematic may represent a component, which may contain component parts. You are more likely to come across the use of components in a PCB schematic. A component is slightly different from an ASIC library cell. A simple example of a component would be a TTL gate, an SN74LS00N, that contains four 2-input NAND gates. We call an SN74LS00N a component and each of the individual NAND gates inside is a component part. Another common example of a component would be a resistor pack—a single package that contains several identical resistors.

In PCB design language a component label or name is a reference designator . A reference designator is a unique name attribute, such as R99 , attached to each component. A reference designator, such as R99 , has two pieces: an alpha prefix R and a numerical suffix 99 . To understand the difference between reference designators and instance names, we need to look at the special requirements of PCB design.

PCBs usually contain packaged ASICs and other ICs that have pins that are soldered to a board. For rectangular, dual-in-line (DIP) packages the pins are numbered counterclockwise from the upper-left corner looking down on the package.

IC symbols have a pin number for each part in the package. For example, the TTL 74174 hex D flip-flop with clear, contains six parts: six identical D flip-flops. The IC symbol representing this device has six PinNumber attribute entries for the D input corresponding to the six possible input pins. They are pins 3, 4, 6, 11, 13, and 14.

When we need a flip-flop in our design, we use a symbol for a 74174 from a schematic library, suppose the symbol name is dffClr . We shall assign a unique instance name to the symbol, CarryFF . Now suppose we need another, identical, flip-flop and we call this BitFF . We do not mind which of the six flip-flop parts in a 74174 we use for CarryFF and BitFF . In fact they do not even have to be in the same package. We shall delay the choice of assigning CarryFF and BitFF to specific packages until we get to the PCB routing step. So at this point on our schematic we do not even know the pin numbers for CarryFF and BitFF . For example the D input to CarryFF could be pin 3, 4, 6, 11, 13, or 14.

The number of wire crossings on a PCB is minimized by careful assignment of components to packages and choice of parts within a package. So the placement-and-routing software may decide which part of which package to use for CarryFF and BitFF depending on which is easier to route. Then, only after the placement and routing is complete, are unique reference designators assigned to the component parts. Only at this point do we know where CarryFF is actually located on the PCB by referring to the reference designator, which points to a specific part in a specific package. Thus CarryFF might be located in IC4 on our PCB. At this point we also know which pins are used for each symbol. So we now know, for example, that the D-input to CarryFF is pin 3 of IC4 .

There is no process in ASIC design directly equivalent to the process of part assignment described above and thus no need to use reference designators. The reference-designator naming convention quickly becomes unwieldy if there are a large number of components in a design. For example, how will we find a NAND gate named X3146 in an ASIC schematic with 100 pages? Instead, for ASICs, we use a naming scheme based on hierarchy.

In large hierarchical ASIC designs it is difficult to provide a unique reference designator to each element. For this reason ASIC designs use instance names to identify the individual components. Meaningful names can be assigned to low-level components and also the symbols that represent hierarchy. We derive the component names by joining all of the higher level cell names together. A special character is used as a delimiter and separates each level.

Examples of hierarchical instance names are:



9.1.7 Connections

Cell instances have terminals that are the inputs and outputs of the cell. Terminals are also known as pins , connectors , or signals . The term pin is widely used, but we shall try to use terminal, and reserve the term pin for the metal leads on an ASIC package. The term pin is used in schematic entry and routing programs that are primarily intended for PCB design.


FIGURE 9.6  An example of the use of a bus to simplify a schematic. (a) An address decoder without using a bus. (b) A bus with bus rippers simplifies the schematic and reduces the possibility of making a mistake in creating and reading the schematic.

Electrical connections between cell instances use wire segments or nets . We can group closely related nets, such as the 32 bits of a 32-bit digital word, together into a bus or into buses (not busses). If signals on a bus are not closely related, we usually use the term bundle or array instead of bus. An example of a bundle might be a bus for a SCSI disk system, containing not only data bits but handshake and control signals too. Figure 9.6 shows an example of a bus in a schematic. If we need to access individual nets in a bus or a bundle, we use a breakout (also known as a ripper , an EDIF term, or extractor ). For example, a breakout is used to access bits 0–7 of a 32-bit bus. If we need to rearrange bits on a bus, some schematic editors offer something called a swizzle . For example, we might use a swizzle to reorder the bits on an 8-bit bus so that the MSB becomes the LSB and so on down to the LSB, which now becomes the MSB. Swizzles can be useful. For example, we can multiply or divide a number by 2 by swizzling all the bits up or down one place on a bus.

9.1.8 Vectored Instances and Buses

So far the naming conventions are fairly standard and easy to follow. However, when we start to use vectored instances and buses (as is now common in large ASICs), there are potential areas of difficulty and confusion. Figure 9.7 (a) shows a schematic for a 16-bit latch that uses multiple copies of the cell FourBit . The buses are labeled with the appropriate bits. Figure 9.7 (b) shows a new cell symbol for the 16-bit latch with 16-bit wide buses for the inputs, D, and outputs, Q.


FIGURE 9.7  A 16-bit latch: (a) drawn as four instances of cell FourBit; (b)  drawn as a cell named SixteenBit; (c) drawn as four multiple instances of cell FourBit.

Figure 9.7 (c) shows an alternative representation of the 16-bit latch using a vectored instance of FourBit with cardinality 4. Suppose we wish to make a connection to expressly one bit, D1 (we have used D1 as the first bit rather than the more conventional D0 so that numbering is easier to follow). We also wish to make a connection to bits D9–D12, represented as D[9:12]. We do this using a bus ripper. Now we have the rather awkward situation of bus naming shown in Figure 9.7 (c). Problems arise when we have “buses of buses” because the numbers for the bus widths do not match on either side of a ripper. For this reason it is best to use the single-bus approach shown in Figure 9.7 (b) rather than the vectored-bus approach of Figure 9.7 (c).

9.1.9 Edit-in-Place

Figure 9.7 (b) shows a symbol SixteenBit , which uses the subschematic shown in Figure 9.7 (a) containing four copies of FourBit , named NB1 , NB2 , NB3 , and NB4 (the NB stands for nibble, which is half of a word; a nibble is 4 bits for 8-bit words). Suppose we use the schematic-entry program to edit the subcell NB1.L1 , which is an instance of DLAT inside NB1 . Perhaps we wish to change the D latch to a D latch with a reset, for example. If the schematic editor supports edit-in-place , we can edit a cell instance directly. After we edit the cell, the program will update all the DLAT subcells in the cell that is currently loaded to reflect the changes that have been made.

To see how edit-in-place works, consider our office building again. Suppose we wish to change some of the offices on each floor from offices without windows to offices with windows. We select the cell instance FloorTwo —that is, an instance of cell Floor . Now we choose the edit mode in the schematic-entry program. But wait! Do we want to edit the cell Floor , or do we want to edit the cell instance FloorTwo ? If we edit the cell Floor , we will be making changes to all of the floors that use cell name Floor —that is, instances FloorTwo through FloorTen . If we edit the cell instance FloorTwo , then the second floor will become different from all the other floors. It will no longer be an instance of cell name Floor and we will have to create another cell name for the cell used by instance FloorTwo . This is like the difference between ordering just one hamburger without pickles and changing the picture on the wall that will change all future hamburgers.

Using edit-in-place we can edit the cell Floor . Suppose we change some of the cell instances of cell name NoWindowOffice to instances of cell name WindowOffice . When we finish editing and save the cell Floor , we have effectively changed all of the floors that contain instances of this cell.

Instead of editing a cell in place, you may really want to edit just one instance of a cell and leave any other instances unchanged. In this case you must create a new cell with a new symbol and new, unique cell name. It might also be wise to change the instance name of the new cell to avoid any confusion.

For example, we might change the third-floor plan of our office to be different from the other upper floors. Suppose the third floor is now an instance of cell name FloorVIP instead of Floor . We could continue to call the third floor cell instance FloorThree , but it would be better to rename the instance differently, FloorSpecial for example, to make it clear that it is different from all the other floors.

Some tools have the ability to alias nets. Aliasing creates a net name from the highest level in the design. Local names are net names at the lowest level such as D , and Q in a flip-flop cell. These local names are automatically replaced by the appropriate top-level names such as Clock1 , or Data2 , using a dictionary . This greatly speeds tracing of signals through a design containing many levels of hierarchy.

9.1.10 Attributes

You can attach a name , also known as an identifier or label , to a component, cell instance, net, terminal, or connector. You can also attach an attribute , or property , which describes some aspect of the component, cell instance, net, or connector. Each attribute has a name, and some attributes also have values. The most common problems in working with schematics and netlists, especially when you try to exchange schematic information between different tools, are problems in naming.

Since cells and their contents have to be stored in a database, a cell name frequently corresponds (or is mapped to) a filename. This then raises the problems of naming conventions including: case sensitivity, name-collision resolution, dictionaries, handling of “common” special characters (such as embedded blanks or underscores), other special characters (such as characters in foreign alphabets), first-character restrictions, name-length problems (only 28 characters are permitted on an NFS compatible filename), and so on.

9.1.11 Netlist Screener

A surprising number of problems can be found by checking a schematic for obviously fatal errors. A program that analyzes a schematic netlist for simple errors is sometimes called a schematic screener or netlist screener . Errors that can be found by a netlist screener include:

  • unconnected cell inputs,
  • unconnected cell outputs,
  • nets not driven by any cells,
  • too many nets driven by one cell,
  • nets driven by more than one cell.

The screener can work continuously as the designer is creating the schematic or can be run as a separate program independently from schematic entry. Usually the designer provides attributes that give the screener the information necessary to perform the checks. A few of the typical attributes that schematic-entry programs use are described next.

A screener usually generates a list of errors together with the locations of the problem on the schematic where appropriate. Some editors associate an identifier, or handle , to every piece of a schematic, including comments and every net. Normally there is some convention to the assigned names such as a grid on a schematic. This works like the locator codes on a map, so that a net with A1 as part of the name is in the upper-left-hand corner, for example. This allows you to quickly and uniquely find any problems found by a screener. The term handle is a computer programming term that is used in referring to a location in memory. Each piece of information on a schematic is stored in lists in memory. This technique breaks down completely when we move to HDLs.

Most schematic-entry programs work on a grid. The designer can control the size of the grid and whether it is visible or not. When you place components or wires you can instruct the editor to force your drawing to snap to grid . This means that drawing a schematic is like drawing on graph paper. You can only locate symbols, wires, and connections on grid points. This simplifies the internal mechanics of the schematic-entry program. It also makes the transfer of schematics between different EDA systems more manageable. Finally, it allows the designer to produce schematic diagrams that are cleaner in appearance and thus easier to read.

Most schematic-entry programs allow you to find components by instance name or cell name. The editor may either jump to the component location and center the graphic window on the component or highlight the component. More sophisticated options allow more complex searches, perhaps using wildcard matching. For example, to find all three-input NAND gates (primitive cell name ND3) or three-input NOR gates (primitive cell name NO3), you could search for cell name N*3, where * is a wildcard symbol standing for any character. The editor may generate a list of components, perhaps with page number and coordinate locations. Extensive find features are useful for large schematics where it quickly becomes impossible to find individual components.

Some schematic editors can complete automatic naming of reference designators or instance names to the schematic symbols either as the editor is running or as a postprocessing step. A component attribute, called a prefix, defines the prefix for the name for each type of component. For example, the prefix for all resistor component types may be R . Each time a prefix is found or a new instance is placed, the number in the reference designator or name is automatically incremented. Thus if the last resistor component type you placed was R99 , the next time you place a resistor it would automatically be named R100 .

For large schematics it is useful to be able to generate a report on the used and unused reference designators. An example would be:

Reference designator prefix: R

Unused reference designator numbers: 153, 154

Last used reference designator number: 180

If you need this feature, you probably are not using enough hierarchy to simplify your design.

During schematic entry of an ASIC design you will frequently need multiple copies of components. This often occurs during datapath design, where operations are carried out across multiple signals on a bus. A common example would be multiple copies of a latch, one for each signal on a bus. It is tedious and inefficient to have to draw and label the same cell many times on a schematic. To simplify this task, most editors allow you to place a special vectored cell instance of a cell. A vectored cell instance, or vectored instance for short, uses the same icon for a single instance but with a special attribute, the cell cardinality , that denotes the number of copies of the cell. Connections between signals on a bus and vectored instances should be handled automatically. The width or cardinality of the bus and the cell cardinality must match, and the design-entry tool should issue a warning if this is not the case.

A schematic-entry program can use a terminal attribute to determine which cell terminals are output terminals and which terminals are input terminals. This attribute is usually called terminal polarity or terminal direction . Possible values for terminal polarity might be: input , output , and bidirectional . Checking the terminal polarity of the terminals on a net can help find problems such as a net with all input terminals or all output terminals.

The fanout of a cell measures the driving capability of an output terminal. The fanin of a cell measures the number of input terminals. Fanout is normally measured using a standard load. A standard load is the load presented by one input of a primitive cell, usually a two-input NAND. For example, a library cell Counter may have an input terminal, Clock , that is connected to the input terminals of five primitive cells. The loading at this terminal is then five standard loads. We say that the fanout of Clock is five. In a similar fashion, we say that if a cell Buffer is capable of driving the inputs of three primitive cells, the fanout of Buffer is three. Using the fanin and fanout attributes a netlist screener can check to see if the fanout driving a net is greater than the sum of all loads on that net. (See Figure 9.2 on page 329.)

9.1.12 Schematic-Entry tools

Some editors offer icon edit-in-place in a similar fashion as schematic edit-in-place for cells. Often you have to toggle editing modes in the schematic-entry program to switch between editing cells and editing cell icons. A schematic-entry program must keep track of when cells are edited. Normally this is done by using a timestamp or datestamp for each cell. This is a text field within the data file for each cell that holds the date and time that the cell was last modified. When a new schematic or cell is loaded, the program needs to compare its timestamp with the timestamps of any subcells. If any of the subcell timestamps are more recent, then the designer needs to be alerted. Usually a message appears to inform you that changes have been made to subcells since the last time the cell currently loaded was saved. This may be what you expect or it may be a warning that somehow a subcell has been changed inadvertently (perhaps someone else changed it) since you last loaded that cell.

Normally the primitive cells in a library are locked and cannot be edited. If you can edit a primitive cell, you have to make a copy, edit the copy, and rename it. Normally the ASIC designer cannot do this and does not want to. For example, to edit a primitive NAND gate stored in an ASIC schematic library would require that the subschematic of the primitive cell be available (usually not the case) and also that the next lower level primitives (symbols for the transistors making up the NAND gate) also be available to the designer (also usually not the case).

What do you do if somehow changes were made to a cell by mistake, perhaps by someone else, and you don’t want the new cell, you want the old version? Most schematic-entry and other EDA tools keep old versions of files as a back-up in case this kind of problem occurs. Most EDA software automatically keeps track of the different versions of a file by appending a version number to each file. Usually this is transparent to the designer. Thus when you edit a cell named Floor , the file on disk might be called Floor.6 . When you save the changes, the software will not overwrite Floor.6 , but write out a new file and automatically name it Floor.7 .

Some design-entry tools are more sophisticated and allow users to create their own libraries as they complete an ASIC design. Designers can then control access to libraries and the cells that they build during a design. This normally requires that a schematic editor, for example, be part of a larger EDA system or framework rather than work as a stand-alone tool. Sometimes the process of library control operates as a separate tool, as a design manager or library manager . Often there is a program similar to the UNIX make command that keeps track of all files, their dependencies, and the tools that are necessary to create and update each file.

You can normally set the number of back-up versions of files that EDA software keeps. The version history controls the number of files the software will keep. If you accidentally update, overwrite, or delete a file, there is usually an option to select and revert to an earlier version. More advanced systems have check-out services (which work just as in source control systems in computer programming databases) that prevent these kinds of problems when many people are working on the same design. Whenever possible, the management of design files and different versions should be left under software control because the process can become very complicated. Reverting to an earlier version of a cell can have drastic consequences for other cells that reference the cell you are working with. Attempts to manually edit files by changing version numbers and timestamps can quickly lead to chaos.

Most schematic-entry programs allow you to undo commands. This feature may be restricted to simply undoing the last command that you entered, or may be an unlimited undo and redo, allowing you to back up as many commands as you want in the current editing session.

You can spend a lot of time in a schematic editor placing components and drawing the connections between them. Features that simplify initial entry and allow modifications to be made easily can make an enormous difference to the efficiency of the schematic-entry process.

Most schematic editors allow you to make connections by dragging the cursor with the wire following behind, in a process known as rubber banding . The connection snaps to a right angle when the connection is completed. For wire connections that require more than two line segments, an automatic wiring feature is useful. This allows you to define the wire path roughly using mouse clicks and have the editor complete the connection.

It is exceedingly painful to move components if you have to rewire connections each time. Most schematic editors allow you to move the components and drag any wires along with them.

One of the most annoying problems that can arise in schematic entry is to think that you have joined two wires on a schematic but find that in reality they do not quite meet. This error can be almost impossible to find. A good editing program will have a way of avoiding this problem. Some editors provide a visual (flash) or audible (beep) feedback when the designer draws a wire that makes an electrical connection with another. Some editors will also automatically insert a dot at a “T” connection to show that an electrical connection is present. Other editors refuse to allow four-way connections to be made, so there can be no ambiguity when wires cross each other if an electrical connection is present or not.

A cell library or a collection of libraries is a key part of the schematic-entry process. The ability to handle and control these libraries is an important feature of any schematic editor. It should be easy to select components from the library to be placed on a schematic.

In large schematics it is necessary to continue large nets and signals across several pages of schematics. Signals such as power and ground, VDD and GND, can be connected using global nets or special connectors . Global nets allow the designer to label a net with the same name at different places on a schematic page or on different pages without having to draw a connection explicitly. The schematic editor treats these nets as though they were electrically connected. Special connector symbols can be used for connections that cross schematic pages. An off-page connector or multipage connector is a special symbol that will show and label a connection to different schematic pages. More sophisticated editors can automatically label these connectors with the page numbers of the destination connectors.

9.1.13 Back-Annotation

After you enter a schematic you simulate the design to make sure it works as expected. This completes the logical design. Next you move to ASIC physical design and complete the layout. Only after you complete the layout do you know the parasitic capacitance and therefore the delay associated with the interconnect. This postroute delay information must be returned to the schematic in a process known as back-annotation . Then you can complete a final, postlayout simulation to make sure that the specifications for the ASIC are met. Chapter 13 covers simulation, and the physical design steps are covered in Chapters 15 to 17.

Chapter start ] [ Previous page ] [ Next page ]

TurboCAD pro : Start at $299

Internet Business Systems © 2016 Internet Business Systems, Inc.
595 Millich Dr., Suite 216, Campbell, CA 95008
+1 (408)-337-6870 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation GISCafe - Geographical Information Services TechJobsCafe - Technical Jobs and Resumes ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy Policy Advertise